Problème wifi mandriva one 2008Fermé

Question

Bonjour,

Je suis débutante en linux.
Apres avoir commencé avec Ubuntu, Kubuntu sans problème, j'ai décidé d'essayer opensuse( que j'ai laissé tombé pour des problème de wifi). Aujourd'hui je suis sur Mandriva one 2008. 
J'ai une clé usb wifi Hercules HWGUSB2-54-V2. Elle est reconnue, je vois meme tous les réseaux wifi de mon voisinage. J'arrive à me connecter au neuf wifi non sécurisé. Apres avoir testé toutes les configurations possibles je n'arrive pas du tout à me connecter au réseau wifi sécurisé.
Je ne sais plus du tout quoi faire.
Je pense que c'est un problème de configuration .
Quelqu'un peut il m'aider?

Merci d'avance

elysium72 · Answer

type de clé WEP / WPA ?

Poca33 · Answer

WPA-PSK

Poca33 · Answer

Tu me parles bien du type de clé qui sécurise mon réseau ?

elysium72 · Answer

oui, je connais pas trop mandriva mais je sais que par default mandriva active le firewall, il faudrait que tu t'orientes dans cette direction (essaye de voir si tu as crontrack d'activer sur mandriva ça s'appelle "le firewall interactif" je crois !)

sinon quelle est le modèle de ta carte ?

si tu le connais pas tape ceci dans une console : lspci | grep Network
et poste ton resultat

Poca33 · Answer

pour ce qui est du modèle de la ma clé usb wifi c'est ==> Ralink 802.11bg wlan rt73 et pour croncrack je cherche .

Poca33 · Answer

Bon alors je n'est pas trouvé crontrack, mais j'ai trouvé le par feu et je l'ai désactivé.

elysium72 · Answer

essaye de taper cette commande dans un terminal en root : modprobe rt73 ou modprobe rt73usb cela devrait charger le module pour ta wifi ensuite réessaye de te connecter


EDIT: il y a pas de "e" a modprobe dsl :p

Poca33 · Answer

Voici tout ce que j'ai essayé ya rien à faire


[root@localhost audrey]# modprobrt73usb
bash: modprobrt73usb: command not found
[root@localhost audrey]# modprobrt73
bash: modprobrt73: command not found
[root@localhost audrey]# modprobert73
bash: modprobert73: command not found
[root@localhost audrey]# modprob
bash: modprob: command not found
[root@localhost audrey]# modprobrt2570
bash: modprobrt2570: command not found
[root@localhost audrey]# modprobrt2500
bash: modprobrt2500: command not found

elysium72 · Answer

excellent sur toutes les tentatives aucune n'a la bonne orthographes :p c:  modprobe rt73   (il y a un espace entre modprobe et rt73)

Poca33 · Answer

il se passe rien

[root@localhost audrey]# modprobe rt73
[root@localhost audrey]#

elysium72 · Answer

c'est normal en facade rien ne se passe mais linux a en fait charger le module de ta carte wifi avec cette commande
donc en gros :

modprobe + nom de ton module a charger = charge le module pour activer son utilisation 
lsmod = liste la totalité des modules charger par ton systeme

maintenant que ton module est chargé et que ton firewall est désactivé tente de te reconnecté avec ta wifi

sinon une astuce quand tu liste tout les modules avec lsmod tu peux y ajouter une fonction de recherche qui va lister un choix en particulier exemple : lsmod | grep rt73 et regarde si il apparait alors il est bien chargé ;) 

ps : le | tu l'obtiens en tapant simultanement la touche [Alt Gr] et [6]

Poca33 · Answer

Voici donc ce qui apparait :

root@localhost audrey]# lsmod|grep rt73
rt73                  212096  0
usbcore               113896  4 rt73,ehci_hcd,uhci_hcd

cela voudrait direque le le module est bien chargé.
mais coté connection rien ne change et c'est super bizarre que je puisse me connecté au réseau non sécurisé et que je ne puisse pas au réseau sécurisé

elysium72 · Answer

ok ok ça se complique mais c'est pas grave alors le module est ok et le firewall aussi tape cette commande et poste ton resultat :
cat /etc/sysconfig/network-scripts/interfaces

Poca33 · Answer

bon j'ai ressayé de me connecté cette fois ci il affiche les barre de force de signal , il y a un point qui apparait de vant mon réseau mais et dis que l'interface wlan est déconnectée .

Poca33 · Answer

en mode normal ==> [audrey@localhost ~]$ cat /etc/sysconfig/network-scripts/interfaces
cat: /etc/sysconfig/network-scripts/interfaces: Aucun fichier ou répertoire de ce type
 en mode root ==> [root@localhost audrey]# cat /etc/sysconfig/network-scripts/interfaces
cat: /etc/sysconfig/network-scripts/interfaces: Aucun fichier ou répertoire de ce type

elysium72 · Answer

autant pour moi c'est :
cat /etc/sysconfig/network-scripts/ifcfg-eth1

ou eventuellement 

/etc/sysconfig/network-scripts/ifcfg-eth0

Poca33 · Answer

[root@localhost audrey]# cat /etc/sysconfig/network-scripts/ifcfg-eth1
cat: /etc/sysconfig/network-scripts/ifcfg-eth1: Aucun fichier ou répertoire de ce type

[root@localhost audrey]# /etc/sysconfig/network-scripts/ifcfg-eth0
bash: /etc/sysconfig/network-scripts/ifcfg-eth0: Permission non accordée

[root@localhost audrey]# /etc/sysconfig/network-scripts/ifcfg-eth1
bash: /etc/sysconfig/network-scripts/ifcfg-eth1: Aucun fichier ou répertoire de ce type

Poca33 · Answer

je veux pas dire mais je trouve que c'est qd meme tres compliqué. heureusement que tu es la et je t'en remercie

elysium72 · Answer

au départ j'ai pas mal galeré avec linux j'étais bien content de rencontré des gens aimables sur les forum Unix/linux alors je le rend

sinon la synthaxe c'est :

cat /etc/sysconfig/network-scripts/ifcfg-eth0

cat /etc/sysconfig/network-scripts/ifcfg-eth1 

il n'y a pas de ":" apres cat 

ps : la fonction cat sert a affiché ce qu'il y a dans un fichier

elysium72 · Answer

a non m***e me suis planter vu que c'est du wifi ça dois etre ça : cat /etc/sysconfig/network-scripts/ifcfg-wlan0

Poca33 · Answer

Voici ce que j'obtiens

Je ne sias pas si c'est utile ou pas mais au moment ou j'ai tapé cette commande ma clé wifi n'était pas branché je suis connecté via l'éthernet


root@localhost audrey]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
BOOTPROTO=dhcp
ONBOOT=yes
[root@localhost audrey]# cat /etc/sysconfig/network-scripts/ifcfg-eth1
cat: /etc/sysconfig/network-scripts/ifcfg-eth1: Aucun fichier ou répertoire de ce type


'ai branché la clé et j'obtiens exactement la meme chose.

cat /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
BOOTPROTO=dhcp
ONBOOT=yes
[root@localhost audrey]# cat /etc/sysconfig/network-scripts/ifcfg-eth1
cat: /etc/sysconfig/network-scripts/ifcfg-eth1: Aucun fichier ou répertoire de ce type

Poca33 · Answer

ok ok je re commence

Poca33 · Answer

[root@localhost audrey]# cat /etc/sysconfig/network-scripts/ifcfg-wlan0
DEVICE=wlan0
BOOTPROTO=dhcp
ONBOOT=yes
METRIC=35
MII_NOT_SUPPORTED=no
USERCTL=yes
RESOLV_MODS=no
WIRELESS_MODE=Managed
WIRELESS_ESSID=NEUF_E144
WIRELESS_ENC_KEY="open s:**********************
IPV6INIT=no
IPV6TO4INIT=no
DHCP_CLIENT=dhclient
NEEDHOSTNAME=no
PEERDNS=yes
PEERYP=yes
PEERNTPD=no

elysium72 · Answer

ok alors tape ça

kedit /etc/sysconfig/network-scripts/ifcfg-wlan0 

cela va ouvrir l'éditeur de texte

a la ligne WIRELESS_ESSID=NEUF_E144 (verifie bien que c'est le bon SSID)

ensuite remplace WIRELESS_ENC_KEY="open s:********************** 

par WIRELESS_ENC_KEY="open s:ta clé WPA

ensuite poste le resultat de ça 

cat /etc/wpa_supplicant.conf

Poca33 · Answer

[root@localhost audrey]# kedit /etc/sysconfig/network-scripts/ifcfg-wlan0
bash: kedit: command not found
 qu'est ce que je fais qui ne vas pas?

elysium72 · Answer

tu as rien fais qui ne vas pas kedit n'est pas installé c tout remplace kedit par kate 
kate /etc/sysconfig/network-scripts/ifcfg-wlan0

Poca33 · Answer

[root@localhost audrey]# kate /etc/sysconfig/network-scripts/ifcfg-wlan0
bash: kate: command not found
 kate n'est pas installé non plus?

elysium72 · Answer

lol non fais urpmi kate ou urpmi kedit et réessaye
limite via msn c plus partique

Poca33 · Answer

ok j'ai installé kedit je te dis ça tout de suite

Poca33 · Answer

[root@localhost audrey]# cat /etc/wpa_supplicant.conf ##### Example wpa_supplicant configuration file ############################### # # This file describes configuration file format and lists all available option. # Please also take a look at simpler configuration examples in 'examples' # subdirectory. # # Empty lines and lines starting with # are ignored # NOTE! This file may contain password information and should probably be made # readable only by root user on multiuser systems. # Note: All file paths in this configuration file should use full (absolute, # not relative to working directory) path in order to allow working directory # to be changed. This can happen if wpa_supplicant is run in the background. # Whether to allow wpa_supplicant to update (overwrite) configuration # # This option can be used to allow wpa_supplicant to overwrite configuration # file whenever configuration is changed (e.g., new network block is added with # wpa_cli or wpa_gui, or a password is changed). This is required for # wpa_cli/wpa_gui to be able to store the configuration changes permanently. # Please note that overwriting configuration file will remove the comments from # it. #update_config=1 # global configuration (shared by all network blocks) # # Parameters for the control interface. If this is specified, wpa_supplicant # will open a control interface that is available for external programs to # manage wpa_supplicant. The meaning of this string depends on which control # interface mechanism is used. For all cases, the existance of this parameter # in configuration is used to determine whether the control interface is # enabled. # # For UNIX domain sockets (default on Linux and BSD): This is a directory that # will be created for UNIX domain sockets for listening to requests from # external programs (CLI/GUI, etc.) for status information and configuration. # The socket file will be named based on the interface name, so multiple # wpa_supplicant processes can be run at the same time if more than one # interface is used. # /var/run/wpa_supplicant is the recommended directory for sockets and by # default, wpa_cli will use it when trying to connect with wpa_supplicant. # # Access control for the control interface can be configured by setting the # directory to allow only members of a group to use sockets. This way, it is # possible to run wpa_supplicant as root (since it needs to change network # configuration and open raw sockets) and still allow GUI/CLI components to be # run as non-root users. However, since the control interface can be used to # change the network configuration, this access needs to be protected in many # cases. By default, wpa_supplicant is configured to use gid 0 (root). If you # want to allow non-root users to use the control interface, add a new group # and change this value to match with that group. Add users that should have # control interface access to this group. If this variable is commented out or # not included in the configuration file, group will not be changed from the # value it got by default when the directory or socket was created. # # When configuring both the directory and group, use following format: # DIR=/var/run/wpa_supplicant GROUP=wheel # DIR=/var/run/wpa_supplicant GROUP=0 # (group can be either group name or gid) # # For UDP connections (default on Windows): The value will be ignored. This # variable is just used to select that the control interface is to be created. # The value can be set to, e.g., udp (ctrl_interface=udp) # # For Windows Named Pipe: This value can be used to set the security descriptor # for controlling access to the control interface. Security descriptor can be # set using Security Descriptor String Format (see https://docs.microsoft.com/en-us/welcome-to-docs # library/default.asp?url=/library/en-us/secauthz/security/ # security_descriptor_string_format.asp). The descriptor string needs to be # prefixed with SDDL=. For example, ctrl_interface=SDDL=D: would set an empty # DACL (which will reject all connections). See README-Windows.txt for more # information about SDDL string format. # ctrl_interface=/var/run/wpa_supplicant # IEEE 802.1X/EAPOL version # wpa_supplicant is implemented based on IEEE Std 802.1X-2004 which defines # EAPOL version 2. However, there are many APs that do not handle the new # version number correctly (they seem to drop the frames completely). In order # to make wpa_supplicant interoperate with these APs, the version number is set # to 1 by default. This configuration value can be used to set it to the new # version (2). eapol_version=1 # AP scanning/selection # By default, wpa_supplicant requests driver to perform AP scanning and then # uses the scan results to select a suitable AP. Another alternative is to # allow the driver to take care of AP scanning and selection and use # wpa_supplicant just to process EAPOL frames based on IEEE 802.11 association # information from the driver. # 1: wpa_supplicant initiates scanning and AP selection # 0: driver takes care of scanning, AP selection, and IEEE 802.11 association # parameters (e.g., WPA IE generation); this mode can also be used with # non-WPA drivers when using IEEE 802.1X mode; do not try to associate with # APs (i.e., external program needs to control association). This mode must # also be used when using wired Ethernet drivers. # 2: like 0, but associate with APs using security policy and SSID (but not # BSSID); this can be used, e.g., with ndiswrapper and NDIS drivers to # enable operation with hidden SSIDs and optimized roaming; in this mode, # the network blocks in the configuration file are tried one by one until # the driver reports successful association; each network block should have # explicit security policy (i.e., only one option in the lists) for # key_mgmt, pairwise, group, proto variables ap_scan=1 # EAP fast re-authentication # By default, fast re-authentication is enabled for all EAP methods that # support it. This variable can be used to disable fast re-authentication. # Normally, there is no need to disable this. fast_reauth=1 # OpenSSL Engine support # These options can be used to load OpenSSL engines. # The two engines that are supported currently are shown below: # They are both from the opensc project (https://opensc.org/ # By default no engines are loaded. # make the opensc engine available #opensc_engine_path=/usr/lib/opensc/engine_opensc.so # make the pkcs11 engine available #pkcs11_engine_path=/usr/lib/opensc/engine_pkcs11.so # configure the path to the pkcs11 module required by the pkcs11 engine #pkcs11_module_path=/usr/lib/pkcs11/opensc-pkcs11.so # Dynamic EAP methods # If EAP methods were built dynamically as shared object files, they need to be # loaded here before being used in the network blocks. By default, EAP methods # are included statically in the build, so these lines are not needed #load_dynamic_eap=/usr/lib/wpa_supplicant/eap_tls.so #load_dynamic_eap=/usr/lib/wpa_supplicant/eap_md5.so # Driver interface parameters # This field can be used to configure arbitrary driver interace parameters. The # format is specific to the selected driver interface. This field is not used # in most cases. #driver_param="field=value" # Maximum lifetime for PMKSA in seconds; default 43200 #dot11RSNAConfigPMKLifetime=43200 # Threshold for reauthentication (percentage of PMK lifetime); default 70 #dot11RSNAConfigPMKReauthThreshold=70 # Timeout for security association negotiation in seconds; default 60 #dot11RSNAConfigSATimeout=60 # network block # # Each network (usually AP's sharing the same SSID) is configured as a separate # block in this configuration file. The network blocks are in preference order # (the first match is used). # # network block fields: # # disabled: # 0 = this network can be used (default) # 1 = this network block is disabled (can be enabled through ctrl_iface, # e.g., with wpa_cli or wpa_gui) # # id_str: Network identifier string for external scripts. This value is passed # to external action script through wpa_cli as WPA_ID_STR environment # variable to make it easier to do network specific configuration. # # ssid: SSID (mandatory); either as an ASCII string with double quotation or # as hex string; network name # # scan_ssid: # 0 = do not scan this SSID with specific Probe Request frames (default) # 1 = scan with SSID-specific Probe Request frames (this can be used to # find APs that do not accept broadcast SSID or use multiple SSIDs; # this will add latency to scanning, so enable this only when needed) # # bssid: BSSID (optional); if set, this network block is used only when # associating with the AP using the configured BSSID # # priority: priority group (integer) # By default, all networks will get same priority group (0). If some of the # networks are more desirable, this field can be used to change the order in # which wpa_supplicant goes through the networks when selecting a BSS. The # priority groups will be iterated in decreasing priority (i.e., the larger the # priority value, the sooner the network is matched against the scan results). # Within each priority group, networks will be selected based on security # policy, signal strength, etc. # Please note that AP scanning with scan_ssid=1 and ap_scan=2 mode are not # using this priority to select the order for scanning. Instead, they try the # networks in the order that used in the configuration file. # # mode: IEEE 802.11 operation mode # 0 = infrastructure (Managed) mode, i.e., associate with an AP (default) # 1 = IBSS (ad-hoc, peer-to-peer) # Note: IBSS can only be used with key_mgmt NONE (plaintext and static WEP) # and key_mgmt=WPA-NONE (fixed group key TKIP/CCMP). In addition, ap_scan has # to be set to 2 for IBSS. WPA-None requires following network block options: # proto=WPA, key_mgmt=WPA-NONE, pairwise=NONE, group=TKIP (or CCMP, but not # both), and psk must also be set. # # frequency: Channel frequency in megahertz (MHz) for IBSS, e.g., # 2412 = IEEE 802.11b/g channel 1. This value is used to configure the initial # channel for IBSS (adhoc) networks. It is ignored in the infrastructure mode. # In addition, this value is only used by the station that creates the IBSS. If # an IBSS network with the configured SSID is already present, the frequency of # the network will be used instead of this configured value. # # proto: list of accepted protocols # WPA = WPA/IEEE 802.11i/D3.0 # RSN = WPA2/IEEE 802.11i (also WPA2 can be used as an alias for RSN) # If not set, this defaults to: WPA RSN # # key_mgmt: list of accepted authenticated key management protocols # WPA-PSK = WPA pre-shared key (this requires 'psk' field) # WPA-EAP = WPA using EAP authentication (this can use an external # program, e.g., Xsupplicant, for IEEE 802.1X EAP Authentication # IEEE8021X = IEEE 802.1X using EAP authentication and (optionally) dynamically # generated WEP keys # NONE = WPA is not used; plaintext or static WEP could be used # If not set, this defaults to: WPA-PSK WPA-EAP # # auth_alg: list of allowed IEEE 802.11 authentication algorithms # OPEN = Open System authentication (required for WPA/WPA2) # SHARED = Shared Key authentication (requires static WEP keys) # LEAP = LEAP/Network EAP (only used with LEAP) # If not set, automatic selection is used (Open System with LEAP enabled if # LEAP is allowed as one of the EAP methods). # # pairwise: list of accepted pairwise (unicast) ciphers for WPA # CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0] # TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0] # NONE = Use only Group Keys (deprecated, should not be included if APs support # pairwise keys) # If not set, this defaults to: CCMP TKIP # # group: list of accepted group (broadcast/multicast) ciphers for WPA # CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0] # TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0] # WEP104 = WEP (Wired Equivalent Privacy) with 104-bit key # WEP40 = WEP (Wired Equivalent Privacy) with 40-bit key [IEEE 802.11] # If not set, this defaults to: CCMP TKIP WEP104 WEP40 # # psk: WPA preshared key; 256-bit pre-shared key # The key used in WPA-PSK mode can be entered either as 64 hex-digits, i.e., # 32 bytes or as an ASCII passphrase (in which case, the real PSK will be # generated using the passphrase and SSID). ASCII passphrase must be between # 8 and 63 characters (inclusive). # This field is not needed, if WPA-EAP is used. # Note: Separate tool, wpa_passphrase, can be used to generate 256-bit keys # from ASCII passphrase. This process uses lot of CPU and wpa_supplicant # startup and reconfiguration time can be optimized by generating the PSK only # only when the passphrase or SSID has actually changed. # # eapol_flags: IEEE 802.1X/EAPOL options (bit field) # Dynamic WEP key required for non-WPA mode # bit0 (1): require dynamically generated unicast WEP key # bit1 (2): require dynamically generated broadcast WEP key # (3 = require both keys; default) # Note: When using wired authentication, eapol_flags must be set to 0 for the # authentication to be completed successfully. # # mixed_cell: This option can be used to configure whether so called mixed # cells, i.e., networks that use both plaintext and encryption in the same # SSID, are allowed when selecting a BSS form scan results. # 0 = disabled (default) # 1 = enabled # # proactive_key_caching: # Enable/disable opportunistic PMKSA caching for WPA2. # 0 = disabled (default) # 1 = enabled # # wep_key0..3: Static WEP key (ASCII in double quotation, e.g. "abcde" or # hex without quotation, e.g., 0102030405) # wep_tx_keyidx: Default WEP key index (TX) (0..3) # # peerkey: Whether PeerKey negotiation for direct links (IEEE 802.11e DLS) is # allowed. This is only used with RSN/WPA2. # 0 = disabled (default) # 1 = enabled #peerkey=1 # # Following fields are only used with internal EAP implementation. # eap: space-separated list of accepted EAP methods # MD5 = EAP-MD5 (unsecure and does not generate keying material -> # cannot be used with WPA; to be used as a Phase 2 method # with EAP-PEAP or EAP-TTLS) # MSCHAPV2 = EAP-MSCHAPv2 (cannot be used separately with WPA; to be used # as a Phase 2 method with EAP-PEAP or EAP-TTLS) # OTP = EAP-OTP (cannot be used separately with WPA; to be used # as a Phase 2 method with EAP-PEAP or EAP-TTLS) # GTC = EAP-GTC (cannot be used separately with WPA; to be used # as a Phase 2 method with EAP-PEAP or EAP-TTLS) # TLS = EAP-TLS (client and server certificate) # PEAP = EAP-PEAP (with tunnelled EAP authentication) # TTLS = EAP-TTLS (with tunnelled EAP or PAP/CHAP/MSCHAP/MSCHAPV2 # authentication) # If not set, all compiled in methods are allowed. # # identity: Identity string for EAP # anonymous_identity: Anonymous identity string for EAP (to be used as the # unencrypted identity with EAP types that support different tunnelled # identity, e.g., EAP-TTLS) # password: Password string for EAP # ca_cert: File path to CA certificate file (PEM/DER). This file can have one # or more trusted CA certificates. If ca_cert and ca_path are not # included, server certificate will not be verified. This is insecure and # a trusted CA certificate should always be configured when using # EAP-TLS/TTLS/PEAP. Full path should be used since working directory may # change when wpa_supplicant is run in the background. # On Windows, trusted CA certificates can be loaded from the system # certificate store by setting this to cert_store://, e.g., # ca_cert="cert_store://CA" or ca_cert="cert_store://ROOT". # Note that when running wpa_supplicant as an application, the user # certificate store (My user account) is used, whereas computer store # (Computer account) is used when running wpasvc as a service. # ca_path: Directory path for CA certificate files (PEM). This path may # contain multiple CA certificates in OpenSSL format. Common use for this # is to point to system trusted CA list which is often installed into # directory like /etc/ssl/certs. If configured, these certificates are # added to the list of trusted CAs. ca_cert may also be included in that # case, but it is not required. # client_cert: File path to client certificate file (PEM/DER) # Full path should be used since working directory may change when # wpa_supplicant is run in the background. # Alternatively, a named configuration blob can be used by setting this # to blob://. # private_key: File path to client private key file (PEM/DER/PFX) # When PKCS#12/PFX file (.p12/.pfx) is used, client_cert should be # commented out. Both the private key and certificate will be read from # the PKCS#12 file in this case. Full path should be used since working # directory may change when wpa_supplicant is run in the background. # Windows certificate store can be used by leaving client_cert out and # configuring private_key in one of the following formats: # cert://substring_to_match # hash://certificate_thumbprint_in_hex # for example: private_key="hash://63093aa9c47f56ae88334c7b65a4" # Note that when running wpa_supplicant as an application, the user # certificate store (My user account) is used, whereas computer store # (Computer account) is used when running wpasvc as a service. # Alternatively, a named configuration blob can be used by setting this # to blob://. # private_key_passwd: Password for private key file (if left out, this will be # asked through control interface) # dh_file: File path to DH/DSA parameters file (in PEM format) # This is an optional configuration file for setting parameters for an # ephemeral DH key exchange. In most cases, the default RSA # authentication does not use this configuration. However, it is possible # setup RSA to use ephemeral DH key exchange. In addition, ciphers with # DSA keys always use ephemeral DH keys. This can be used to achieve # forward secrecy. If the file is in DSA parameters format, it will be # automatically converted into DH params. # subject_match: Substring to be matched against the subject of the # authentication server certificate. If this string is set, the server # sertificate is only accepted if it contains this string in the subject. # The subject string is in following format: # /C=US/ST=CA/L=San Francisco/CN=Test AS/emailAddress=as@example.com # altsubject_match: Semicolon separated string of entries to be matched against # the alternative subject name of the authentication server certificate. # If this string is set, the server sertificate is only accepted if it # contains one of the entries in an alternative subject name extension. # altSubjectName string is in following format: TYPE:VALUE # Example: EMAIL:server@example.com # Example: DNS:server.example.com;DNS:server2.example.com # Following types are supported: EMAIL, DNS, URI # phase1: Phase1 (outer authentication, i.e., TLS tunnel) parameters # (string with field-value pairs, e.g., "peapver=0" or # "peapver=1 peaplabel=1") # 'peapver' can be used to force which PEAP version (0 or 1) is used. # 'peaplabel=1' can be used to force new label, "client PEAP encryption", # to be used during key derivation when PEAPv1 or newer. Most existing # PEAPv1 implementation seem to be using the old label, "client EAP # encryption", and wpa_supplicant is now using that as the default value. # Some servers, e.g., Radiator, may require peaplabel=1 configuration to # interoperate with PEAPv1; see eap_testing.txt for more details. # 'peap_outer_success=0' can be used to terminate PEAP authentication on # tunneled EAP-Success. This is required with some RADIUS servers that # implement draft-josefsson-pppext-eap-tls-eap-05.txt (e.g., # Lucent NavisRadius v4.4.0 with PEAP in "IETF Draft 5" mode) # include_tls_length=1 can be used to force wpa_supplicant to include # TLS Message Length field in all TLS messages even if they are not # fragmented. # sim_min_num_chal=3 can be used to configure EAP-SIM to require three # challenges (by default, it accepts 2 or 3) # phase2: Phase2 (inner authentication with TLS tunnel) parameters # (string with field-value pairs, e.g., "auth=MSCHAPV2" for EAP-PEAP or # "autheap=MSCHAPV2 autheap=MD5" for EAP-TTLS) # Following certificate/private key fields are used in inner Phase2 # authentication when using EAP-TTLS or EAP-PEAP. # ca_cert2: File path to CA certificate file. This file can have one or more # trusted CA certificates. If ca_cert2 and ca_path2 are not included, # server certificate will not be verified. This is insecure and a trusted # CA certificate should always be configured. # ca_path2: Directory path for CA certificate files (PEM) # client_cert2: File path to client certificate file # private_key2: File path to client private key file # private_key2_passwd: Password for private key file # dh_file2: File path to DH/DSA parameters file (in PEM format) # subject_match2: Substring to be matched against the subject of the # authentication server certificate. # altsubject_match2: Substring to be matched against the alternative subject # name of the authentication server certificate. # # fragment_size: Maximum EAP fragment size in bytes (default 1398). # This value limits the fragment size for EAP methods that support # fragmentation (e.g., EAP-TLS and EAP-PEAP). This value should be set # small enough to make the EAP messages fit in MTU of the network # interface used for EAPOL. The default value is suitable for most # cases. # # EAP-PSK variables: # eappsk: 16-byte (128-bit, 32 hex digits) pre-shared key in hex format # nai: user NAI # # EAP-PAX variables: # eappsk: 16-byte (128-bit, 32 hex digits) pre-shared key in hex format # # EAP-SAKE variables: # eappsk: 32-byte (256-bit, 64 hex digits) pre-shared key in hex format # (this is concatenation of Root-Secret-A and Root-Secret-B) # nai: user NAI (PEERID) # # EAP-GPSK variables: # eappsk: Pre-shared key in hex format (at least 128 bits, i.e., 32 hex digits) # nai: user NAI (ID_Client) # # EAP-FAST variables: # pac_file: File path for the PAC entries. wpa_supplicant will need to be able # to create this file and write updates to it when PAC is being # provisioned or refreshed. Full path to the file should be used since # working directory may change when wpa_supplicant is run in the # background. Alternatively, a named configuration blob can be used by # setting this to blob:// # phase1: fast_provisioning option can be used to enable in-line provisioning # of EAP-FAST credentials (PAC): # 0 = disabled, # 1 = allow unauthenticated provisioning, # 2 = allow authenticated provisioning, # 3 = allow both unauthenticated and authenticated provisioning # fast_max_pac_list_len= option can be used to set the maximum # number of PAC entries to store in a PAC list (default: 10) # fast_pac_format=binary option can be used to select binary format for # storing PAC entires in order to save some space (the default # text format uses about 2.5 times the size of minimal binary # format) # # wpa_supplicant supports number of "EAP workarounds" to work around # interoperability issues with incorrectly behaving authentication servers. # These are enabled by default because some of the issues are present in large # number of authentication servers. Strict EAP conformance mode can be # configured by disabling workarounds with eap_workaround=0. # Example blocks: # Simple case: WPA-PSK, PSK as an ASCII passphrase, allow all valid ciphers # network={ # ssid="simple" # psk="very secret passphrase" # priority=5 # } # Same as previous, but request SSID-specific scanning (for APs that reject # broadcast SSID) # network={ # ssid="second ssid" # scan_ssid=1 # psk="very secret passphrase" # priority=2 # } # Only WPA-PSK is used. Any valid cipher combination is accepted. # network={ # ssid="example" # proto=WPA # key_mgmt=WPA-PSK # pairwise=CCMP TKIP # group=CCMP TKIP WEP104 WEP40 # psk=06b4be19da289f475aa46a33cb793029d4ab3db7a23ee92382eb0106c72ac7bb # priority=2 # } # Only WPA-EAP is used. Both CCMP and TKIP is accepted. An AP that used WEP104 # or WEP40 as the group cipher will not be accepted. # network={ # ssid="example" # proto=RSN # key_mgmt=WPA-EAP # pairwise=CCMP TKIP # group=CCMP TKIP # eap=TLS # identity="user@example.com" # ca_cert="/etc/cert/ca.pem" # client_cert="/etc/cert/user.pem" # private_key="/etc/cert/user.prv" # private_key_passwd="password" # priority=1 # } # EAP-PEAP/MSCHAPv2 configuration for RADIUS servers that use the new peaplabel # (e.g., Radiator) # network={ # ssid="example" # key_mgmt=WPA-EAP # eap=PEAP # identity="user@example.com" # password="foobar" # ca_cert="/etc/cert/ca.pem" # phase1="peaplabel=1" # phase2="auth=MSCHAPV2" # priority=10 # } # EAP-TTLS/EAP-MD5-Challenge configuration with anonymous identity for the # unencrypted use. Real identity is sent only within an encrypted TLS tunnel. # network={ # ssid="example" # key_mgmt=WPA-EAP # eap=TTLS # identity="user@example.com" # anonymous_identity="anonymous@example.com" # password="foobar" # ca_cert="/etc/cert/ca.pem" # priority=2 # } # EAP-TTLS/MSCHAPv2 configuration with anonymous identity for the unencrypted # use. Real identity is sent only within an encrypted TLS tunnel. # network={ # ssid="example" # key_mgmt=WPA-EAP # eap=TTLS # identity="user@example.com" # anonymous_identity="anonymous@example.com" # password="foobar" # ca_cert="/etc/cert/ca.pem" # phase2="auth=MSCHAPV2" # } # WPA-EAP, EAP-TTLS with different CA certificate used for outer and inner # authentication. # network={ # ssid="example" # key_mgmt=WPA-EAP # eap=TTLS # # Phase1 / outer authentication # anonymous_identity="anonymous@example.com" # ca_cert="/etc/cert/ca.pem" # # Phase 2 / inner authentication # phase2="autheap=TLS" # ca_cert2="/etc/cert/ca2.pem" # client_cert2="/etc/cer/user.pem" # private_key2="/etc/cer/user.prv" # private_key2_passwd="password" # priority=2 # } # Both WPA-PSK and WPA-EAP is accepted. Only CCMP is accepted as pairwise and # group cipher. # network={ # ssid="example" # bssid=00:11:22:33:44:55 # proto=WPA RSN # key_mgmt=WPA-PSK WPA-EAP # pairwise=CCMP # group=CCMP # psk=06b4be19da289f475aa46a33cb793029d4ab3db7a23ee92382eb0106c72ac7bb # } # Special characters in SSID, so use hex string. Default to WPA-PSK, WPA-EAP # and all valid ciphers. # network={ # ssid=00010203 # psk=000102030405060708090a0b0c0d0e0f101112131415161718191a1b1c1d1e1f # } # EAP-SIM with a GSM SIM or USIM # network={ # ssid="eap-sim-test" # key_mgmt=WPA-EAP # eap=SIM # pin="1234" # pcsc="" # } # EAP-PSK # network={ # ssid="eap-psk-test" # key_mgmt=WPA-EAP # eap=PSK # identity="eap_psk_user" # eappsk=06b4be19da289f475aa46a33cb793029 # nai="eap_psk_user@example.com" # } # IEEE 802.1X/EAPOL with dynamically generated WEP keys (i.e., no WPA) using # EAP-TLS for authentication and key generation; require both unicast and # broadcast WEP keys. # network={ # ssid="1x-test" # key_mgmt=IEEE8021X # eap=TLS # identity="user@example.com" # ca_cert="/etc/cert/ca.pem" # client_cert="/etc/cert/user.pem" # private_key="/etc/cert/user.prv" # private_key_passwd="password" # eapol_flags=3 # } # LEAP with dynamic WEP keys # network={ # ssid="leap-example" # key_mgmt=IEEE8021X # eap=LEAP # identity="user" # password="foobar" # } # EAP-FAST with WPA (WPA or WPA2) # network={ # ssid="eap-fast-test" # key_mgmt=WPA-EAP # eap=FAST # anonymous_identity="FAST-000102030405" # identity="username" # password="password" # phase1="fast_provisioning=1" # pac_file="/etc/wpa_supplicant.eap-fast-pac" # } # network={ # ssid="eap-fast-test" # key_mgmt=WPA-EAP # eap=FAST # anonymous_identity="FAST-000102030405" # identity="username" # password="password" # phase1="fast_provisioning=1" # pac_file="blob://eap-fast-pac" # } # Plaintext connection (no WPA, no IEEE 802.1X) # network={ # ssid="plaintext-test" # key_mgmt=NONE # } # Shared WEP key connection (no WPA, no IEEE 802.1X) # network={ # ssid="static-wep-test" # key_mgmt=NONE # wep_key0="abcde" # wep_key1=0102030405 # wep_key2="1234567890123" # wep_tx_keyidx=0 # priority=5 # } # Shared WEP key connection (no WPA, no IEEE 802.1X) using Shared Key # IEEE 802.11 authentication # network={ # ssid="static-wep-test2" # key_mgmt=NONE # wep_key0="abcde" # wep_key1=0102030405 # wep_key2="1234567890123" # wep_tx_keyidx=0 # priority=5 # auth_alg=SHARED # } # IBSS/ad-hoc network with WPA-None/TKIP. # network={ # ssid="test adhoc" # mode=1 # frequency=2412 # proto=WPA # key_mgmt=WPA-NONE # pairwise=NONE # group=TKIP # psk="secret passphrase" # } # Catch all example that allows more or less all configuration modes # network={ # ssid="example" # scan_ssid=1 # key_mgmt=WPA-EAP WPA-PSK IEEE8021X NONE # pairwise=CCMP TKIP # group=CCMP TKIP WEP104 WEP40 # psk="very secret passphrase" # eap=TTLS PEAP TLS # identity="user@example.com" # password="foobar" # ca_cert="/etc/cert/ca.pem" # client_cert="/etc/cert/user.pem" # private_key="/etc/cert/user.prv" # private_key_passwd="password" # phase1="peaplabel=0" # } # Example of EAP-TLS with smartcard (openssl engine) # network={ # ssid="example" # key_mgmt=WPA-EAP # eap=TLS # proto=RSN # pairwise=CCMP TKIP # group=CCMP TKIP # identity="user@example.com" # ca_cert="/etc/cert/ca.pem" # client_cert="/etc/cert/user.pem" # # engine=1 # # # The engine configured here must be available. Look at # # OpenSSL engine support in the global section. # # The key available through the engine must be the private key # # matching the client certificate configured above. # # # use the opensc engine # #engine_id="opensc" # #key_id="45" # # # use the pkcs11 engine # engine_id="pkcs11" # key_id="id_45" # # # Optional PIN configuration; this can be left out and PIN will be # # asked through the control interface # pin="1234" # } # Example configuration showing how to use an inlined blob as a CA certificate # data instead of using external file # network={ # ssid="example" # key_mgmt=WPA-EAP # eap=TTLS # identity="user@example.com" # anonymous_identity="anonymous@example.com" # password="foobar" # ca_cert="blob://exampleblob" # priority=20 # } blob-base64-exampleblob={ SGVsbG8gV29ybGQhCg== } # Wildcard match for SSID (plaintext APs only). This example select any # open AP regardless of its SSID. # network={ # key_mgmt=NONE # } ça fait un peu charabia

elysium72 · Answer

fait: kedit /etc/wpa_supplicant.conf 
et a la tout fin de ton fichier rajoute ces qq lignes

network={
psk="ta clé WPA"    # rajoute ta clé surtout
scan_ssid=1
ssid="NEUF_E144"  # pareil verife bien que c'est le bon SSID
} 

enregistre et ferme kedit


refait :

kedit /etc/sysconfig/network-scripts/ifcfg-wlan0 

et a la ligne WIRELESS_ENC_KEY="open s:ta clé WPA 
pense a finir la ligne par un " ça doit donner ça WIRELESS_ENC_KEY="open s:ta clé WPA"

enrgistre et ferme
et toujours dans un terminal fait

/etc/rc.d/network restart

croise les doigts pour que cela fonctionne

Poca33 · Answer

[root@localhost audrey]# /etc/rc.d/network restart
bash: /etc/rc.d/network: Aucun fichier ou répertoire de ce type
[root@localhost audrey]#

c'est normal?
 
j'essai de me connecté via le wifi ça donne rien

il demande constament une adresse réseau pour l'interface wlan0 (protocole dhcp)

bon je pense que ja vais arreter la pour ce soir et commencer à réfléchir à ma prochaine distribution

en tout cas merci pour ton aide

bonne soirée

Poca33 · Answer

Salut,

Ja'ia bien laissé tombé Mandriva. C'est dommage cette distrib me plaisiat beaucoup. J'ai du revenir à Ubuntu, que je trouve tres simpliste mais au moins mon wifi fonctionne. 

Dans l'attente de trouver une distribution avec laquelle mon wifi fonctionnerai.

Elysium72, merci d'avoir pris du temps pour essayer de résoudre mon problème.

Problème wifi mandriva one 2008

33 réponses

Discussions similaires

Newsletters