Installation AIR-LAP1262N-E-K9

Quand tu te sera branché en console, tu peux donner une adresse IP au port de ton choix en faisant les commandes suivantes :
en (enter)
sh run (là tu récupère le nom de ton port ethernet borne)
conf t (enter)
int <nom port ethernet> (enter)
ip address <adresse IP> <masque> (enter)
no sh

ensuite tu peux la choper via interface web

Bonjour et merci de ta réponse
Voici ce que j’obtiens en raccordant la borne Wifi AIR-LAP1262N-E-K9 par la console avec le logiciel Putty ( la RJ45 Ethernet n'est pas raccordée)


r WRDTR,CLKTR: 0x8200083f 0x40000000
r RQDC ,RFDC : 0x80000030 0x0000021b

using eeprom values

WRDTR,CLKTR: 0x8200083f 0x40000000
RQDC ,RFDC : 0x80000030 0x0000021b

using MCNG ddr static values from serial eeprom
ddr init done

Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
................................................................................ ................................................................................ ................................................................................ ......
Xmodem file system is available.

DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x8200083f, 0x40000000
RQDC, RFDC : 0x80000030, 0x0000021b

PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
64bit PCIE devices
PCIEx: initialization done
flashfs[0]: 66 files, 15 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 20732928
flashfs[0]: Bytes available: 11006976
flashfs[0]: flashfs fsck took 10 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: c4:64:13:11:27:22
Waiting for PHY auto negotiation to complete... TIMEOUT !
Ethernet link is down.
Error: RGMII speed

The system has encountered an error initializing
the Ethernet port.
The system is ignoring the error and continuing to boot.
If you abort the system boot process, the following
commands will re-initialize Ethernet, TFTP, and finish
loading the operating system software:

ether_init
tftp_init
boot

Loading "flash:/ap3g1-k9w8-mx.152-2.JB3/ap3g1-k9w8-xx.152-2.JB3"...############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################

File "flash:/ap3g1-k9w8-mx.152-2.JB3/ap3g1-k9w8-xx.152-2.JB3" uncompressed and installed, entry point: 0x100000
executing...
enet halted

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco IOS Software, C1260 Software (AP3G1-K9W8-M), Version 15.2(2)JB3, RELEASE SOFTWARE (fc1)
Technical Support: https://www.cisco.com/c/en/us/support/index.html
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 19-Dec-13 03:43 by prod_rel_team

Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
......................................................................................................................................................................................................................................................

flashfs[3]: 66 files, 15 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 31481856
flashfs[3]: Bytes used: 20732928
flashfs[3]: Bytes available: 10748928
flashfs[3]: flashfs fsck took 8 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete....done Initializing flashfs.

Waiting for PHY auto negotiation to complete... TIMEOUT !
Ethernet link is down.
Error: RGMII speed

Radio0 present 8364B 8000 B8020000 0 B8030000 10
Rate table has 80 entries (32 SGI/4 BF variants)

Radio1 present 8364B 8000 B0020000 0 B0030000 C
This product contains cryptographic features and is subject to United
memory validate-checksum 30
^
% Invalid input detected at '^' marker.

login authentication default
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
^
% Invalid input detected at '^' marker.

third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
https://pepd.cloudapps.cisco.com/legal/export/pepd/Search.do

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-LAP1262N-E-K9 (PowerPC460exr) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FCZ1552Z86W
PowerPC460exr CPU at 666Mhz, revision number 0x18A8
Last reset from power-on
LWAPP image version 7.4.121.0
1 Gigabit Ethernet interface
2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C4:64:13:11:27:22
Part Number : 73-12175-05
PCA Assembly Number : 800-32268-05
PCA Revision Number : A0
PCB Serial Number : FOC15483P1K
Top Assembly Part Number : 800-33866-01
Top Assembly Serial Number : FCZ1552Z86W
Top Revision Number : A0
Product/Model Number : AIR-LAP1262N-E-K9
% Please define a domain-name first.


Press RETURN to get started!

• Mar 1 00:00:10.129: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
• Mar 1 00:00:10.129: *** CRASH_LOG = YES
• Mar 1 00:00:10.129: 64bit PCIE devicesSecurity Core found.

Base Ethernet MAC address: C4:64:13:11:27:22

• Mar 1 00:00:51.854: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
• Mar 1 00:00:55.087: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
• Mar 1 00:00:58.441: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
• Mar 1 00:01:01.571: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1260 Software (AP3G1-K9W8-M), Version 15.2(2)JB3, RELEASE SOFTWARE (fc1)
Technical Support: https://www.cisco.com/c/en/us/support/index.html
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 19-Dec-13 03:43 by prod_rel_team

• Mar 1 00:01:01.571: %SNMP-5-COLDSTART: SNMP agent on host LAC-LAP-114 is undergoing a cold start
• Mar 1 00:01:01.612: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
• Mar 1 00:01:01.618: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
• Mar 1 00:01:01.659: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
• Mar 1 00:01:01.819: %SSH-5-ENABLED: SSH 2.0 has been enabled
• Mar 1 00:01:01.819: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
• Mar 1 00:01:02.609: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
• Mar 1 00:01:02.700: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
• Mar 1 00:01:03.694: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
• Mar 1 00:01:03.776: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
• Mar 1 00:01:03.782: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
• Mar 1 00:01:03.789: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
• Mar 1 00:01:04.776: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
• Mar 1 00:01:04.783: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
• Mar 1 00:01:04.805: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
• Mar 1 00:01:05.805: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up%Default route without gateway, if not a point-to-point interface, may impact performance
• Mar 1 00:01:30.077: Logging LWAPP message to 255.255.255.255.
• Mar 1 00:01:32.062: %LINK-6-UPDOWN: Interface BVI1, changed state to down
• Mar 1 00:01:33.063: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
• Mar 1 00:01:40.090: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
• Mar 1 00:01:50.091: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
• Mar 1 00:02:00.091: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
• Mar 1 00:02:10.091: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!