Raspberry pi 3 en HOT spot wifi

Bonjour, donc le portail captif sais tous a fait cela.
Mais comment configurer ma raspberry pi pour créé un réseau wifi tel un routeur ?

Voici la carte wifi:

pi@serveurFTP:~ $ iw list
Wiphy phy0
max # scan SSIDs: 10
max scan IEs length: 2048 bytes
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports T-DLS.
Supported Ciphers:

• WEP40 (00-0f-ac:1)
• WEP104 (00-0f-ac:5)
• TKIP (00-0f-ac:2)
• CCMP (00-0f-ac:4)
• CMAC (00-0f-ac:6)

Available Antennas: TX 0 RX 0
Supported interface modes:

• IBSS
• managed
• AP
• P2P-client
• P2P-GO
• P2P-device

Band 1:
Capabilities: 0x1020
HT20
Static SM Power Save
RX HT20 SGI
No RX STBC
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-7
Bitrates (non-HT):

• 1.0 Mbps
• 2.0 Mbps (short preamble supported)
• 5.5 Mbps (short preamble supported)
• 11.0 Mbps (short preamble supported)
• 6.0 Mbps
• 9.0 Mbps
• 12.0 Mbps
• 18.0 Mbps
• 24.0 Mbps
• 36.0 Mbps
• 48.0 Mbps
• 54.0 Mbps

Frequencies:

• 2412 MHz [1] (20.0 dBm)
• 2417 MHz [2] (20.0 dBm)
• 2422 MHz [3] (20.0 dBm)
• 2427 MHz [4] (20.0 dBm)
• 2432 MHz [5] (20.0 dBm)
• 2437 MHz [6] (20.0 dBm)
• 2442 MHz [7] (20.0 dBm)
• 2447 MHz [8] (20.0 dBm)
• 2452 MHz [9] (20.0 dBm)
• 2457 MHz [10] (20.0 dBm)
• 2462 MHz [11] (20.0 dBm)
• 2467 MHz [12] (20.0 dBm)
• 2472 MHz [13] (20.0 dBm)
• 2484 MHz [14] (disabled)

Supported commands:

• new_interface
• set_interface
• new_key
• start_ap
• join_ibss
• set_pmksa
• del_pmksa
• flush_pmksa
• remain_on_channel
• frame
• set_channel
• tdls_oper
• start_sched_scan
• start_p2p_device
• crit_protocol_start
• crit_protocol_stop
• connect
• disconnect

Supported TX frame types:

• managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
• P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
• P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
• P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0

Supported RX frame types:

• managed: 0x40 0xd0
• P2P-client: 0x40 0xd0
• P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
• P2P-device: 0x40 0xd0

software interface modes (can always be added):
valid interface combinations:

• #{ managed } <= 1, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1,

total <= 3, #channels <= 2

• #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1,

total <= 4, #channels <= 1
Device supports scan flush.

Configuration file: /etc/hostapd/hostapd.conf
Line 18: no authentication algorithms allowed

cat -n /etc/hostapd/hostapd.conf

pour avoir une meilleure idée concernant la ligne n° 18 ;-\

Bonjour merci, donc ça vient de la:

17 # Wi-Fi ouvert, pas d'authentification !
18 auth_algs=0


Voici la totalité :

1
2 # interface wlan du Wi-Fi
3 interface=wlan0
4
5 # nl80211 avec tous les drivers Linux mac80211
6 driver=nl80211
7
8 # Nom du spot Wi-Fi
9 ssid=Free Video
10
11 # mode Wi-Fi (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g)
12 hw_mode=g
13
14 # canal de fréquence Wi-Fi (1-14)
15 channel=6
16
17 # Wi-Fi ouvert, pas d'authentification !
18 auth_algs=0
19
20 # Beacon interval in kus (1.024 ms)
21 beacon_int=100
22
23 # DTIM (delivery trafic information message)
24 dtim_period=2
25
26 # Maximum number of stations allowed in station table
27 max_num_sta=255
28
29 # RTS/CTS threshold; 2347 = disabled (default)
30 rts_threshold=2347
31
32 # Fragmentation threshold; 2346 = disabled (default)
33 fragm_threshold=2346


J'ai pris cette configuration sur le site: https://doc.ubuntu-fr.org/hostapd

Re j'ai modifier le fichier de configuration:

1
2 # interface wlan du Wi-Fi
3 interface=wlan0
4
5 # nl80211 avec tous les drivers Linux mac80211
6 driver=nl80211
7
8 # Nom du spot Wi-Fi
9 ssid=Free Video
10
11 # mode Wi-Fi (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g)
12 hw_mode=g
13
14 # canal de fréquence Wi-Fi (1-14)
15 channel=6
16
17 # Wi-Fi ouvert, pas d'authentification ! passage a 1
18 auth_algs=1
19
20 # Beacon interval in kus (1.024 ms)
21 beacon_int=100
22
23 # DTIM (delivery trafic information message)
24 dtim_period=2
25
26 # Maximum number of stations allowed in station table
27 max_num_sta=255
28
29 # RTS/CTS threshold; 2347 = disabled (default)
30 rts_threshold=2347
31
32 # Fragmentation threshold; 2346 = disabled (default)
33 fragm_threshold=2346

Mais la pu rien ne ce passe : Après ces deux commandes :

pi@serveurFTP:~ $ sudo service dnsmasq start
pi@serveurFTP:~ $ sudo service hostapd start

Le nom SSID Free Video n'apparait pas :/
Aucun messages rien.