A voir également:
- Serveur proxy ubuntu squid
- Serveur proxy ps4 ✓ - Forum Réseaux sociaux
- Telecharger ubuntu - Télécharger - Systèmes d'exploitation
- Une erreur applicative s'est produite sur le serveur adelie. - Forum Réseaux sociaux
- OU TROUVER MON ADRESSE PROXY ✓ - Forum Windows
- Serveur pop - Guide
2 réponses
# WELCOME TO SQUID 3.1.19
# ----------------------------
#
# This is the documentation for the Squid configuration file.
# This documentation can also be found online at:
# http://www.squid-cache.org/Doc/config/
#
# You may wish to look at the Squid home page and wiki for the
# FAQ and other documentation:
# http://www.squid-cache.org/
# http://wiki.squid-cache.org/SquidFaq
# http://wiki.squid-cache.org/ConfigExamples
#
# This documentation shows what the defaults for various directives
# happen to be. If you don't need to change the default, you should
# leave the line out of your squid.conf in most cases.
#
# In some cases "none" refers to no default setting at all,
# while in other cases it refers to the value of the option
# - the comments for that keyword indicate if this is the case.
#
# Configuration options can be included using the "include" directive.
# Include takes a list of files to include. Quoting and wildcards are
# supported.
#
# For example,
#
# include /path/to/included/file/squid.acl.config
#
# Includes can be nested up to a hard-coded depth of 16 levels.
# This arbitrary restriction is to prevent recursive include references
# from causing Squid entering an infinite loop whilst trying to load
# configuration files.
# TAG: dns_testnames
# Remove this line. DNS is no longer tested on startup.
#Default:
# none
# TAG: extension_methods
# Remove this line. All valid methods for HTTP are accepted by default.
#Default:
# none
# TAG: incoming_rate
#Default:
# none
# TAG: server_http11
# Remove this line. HTTP/1.1 is supported by default.
#Default:
# none
# TAG: upgrade_http0.9
# Remove this line. ICY/1.0 streaming protocol is supported by default.
#Default:
# none
# TAG: zph_local
# Alter these entries. Use the qos_flows directive instead.
#Default:
# none
# TAG: header_access
# Since squid-3.0 replace with request_header_access or reply_header_access
# depending on whether you wish to match client requests or server replies.
#Default:
# none
# TAG: httpd_accel_no_pmtu_disc
# Since squid-3.0 use the 'disable-pmtu-discovery' flag on http_port instead.
#Default:
# none
# OPTIONS FOR AUTHENTICATION
# -----------------------------------------------------------------------------
# TAG: auth_param
# This is used to define parameters for the various authentication
# schemes supported by Squid.
#
# format: auth_param scheme parameter [setting]
#
# The order in which authentication schemes are presented to the client is
# dependent on the order the scheme first appears in config file. IE
# has a bug (it's not RFC 2617 compliant) in that it will use the basic
# scheme if basic is the first entry presented, even if more secure
# schemes are presented. For now use the order in the recommended
# settings section below. If other browsers have difficulties (don't
# recognize the schemes offered even if you are using basic) either
# put basic first, or disable the other schemes (by commenting out their
# program entry).
#
# Once an authentication scheme is fully configured, it can only be
# shutdown by shutting squid down and restarting. Changes can be made on
# the fly and activated with a reconfigure. I.E. You can change to a
# different helper, but not unconfigure the helper completely.
#
# Please note that while this directive defines how Squid processes
# authentication it does not automatically activate authentication.
# To use authentication you must in addition make use of ACLs based
# on login name in http_access (proxy_auth, proxy_auth_regex or
# external with %LOGIN used in the format tag). The browser will be
# challenged for authentication on the first such acl encountered
# in http_access processing and will also be re-challenged for new
# login credentials if the request is being denied by a proxy_auth
# type acl.
#
# WARNING: authentication can't be used in a transparently intercepting
# proxy as the client then thinks it is talking to an origin server and
# not the proxy. This is a limitation of bending the TCP/IP protocol to
# transparently intercepting port 80, not a limitation in Squid.
# Ports flagged 'transparent', 'intercept', or 'tproxy' have
# authentication disabled.
#
# === Parameters for the basic scheme follow. ===
#
# "program" cmdline
# Specify the command for the external authenticator. Such a program
# reads a line containing "username password" and replies "OK" or
# "ERR" in an endless loop. "ERR" responses may optionally be followed
# by a error description available as %m in the returned error page.
# If you use an authenticator, make sure you have 1 acl of type
# proxy_auth.
#
# By default, the basic authentication scheme is not used unless a
# program is specified.
#
# If you want to use the traditional NCSA proxy authentication, set
# this line to something like
#
# auth_param basic program /usr/lib/squid3/ncsa_auth /usr/etc/passwd
#
# "utf8" on|off
# HTTP uses iso-latin-1 as characterset, while some authentication
# backends such as LDAP expects UTF-8. If this is set to on Squid will
# translate the HTTP iso-latin-1 charset to UTF-8 before sending the
# username & password to the helper.
#
# "children" numberofchildren
# The number of authenticator processes to spawn. If you start too few
# Squid will have to wait for them to process a backlog of credential
# verifications, slowing it down. When password verifications are
# done via a (slow) network you are likely to need lots of
# authenticator processes.
# auth_param basic children 5
#
# "concurrency" concurrency
# The number of concurrent requests the helper can process.
# The default of 0 is used for helpers who only supports
# one request at a time. Setting this changes the protocol used to
# include a channel number first on the request/response line, allowing
# multiple requests to be sent to the same helper in parallell without
# wating for the response.
# Must not be set unless it's known the helper supports this.
# auth_param basic concurrency 0
#
# "realm" realmstring
# Specifies the realm name which is to be reported to the
# client for the basic proxy authentication scheme (part of
# the text the user will see when prompted their username and
# password). There is no default.
# auth_param basic realm Squid proxy-caching web server
#
# "credentialsttl" timetolive
# Specifies how long squid assumes an externally validated
# username:password pair is valid for - in other words how
# often the helper program is called for that user. Set this
# low to force revalidation with short lived passwords. Note
# setting this high does not impact your susceptibility
# to replay attacks unless you are using an one-time password
# system (such as SecureID). If you are using such a system,
# you will be vulnerable to replay attacks unless you also
# use the max_user_ip ACL in an http_access rule.
#
# "casesensitive" on|off
# Specifies if usernames are case sensitive. Most user databases are
# case insensitive allowing the same username to be spelled using both
# lower and upper case letters, but some are case sensitive. This
# makes a big difference for user_max_ip ACL processing and similar.
# auth_param basic casesensitive off
#
# === Parameters for the digest scheme follow ===
#
# "program" cmdline
# Specify the command for the external authenticator. Such
# a program reads a line containing "username":"realm" and
# replies with the appropriate H(A1) value hex encoded or
# ERR if the user (or his H(A1) hash) does not exists.
# See rfc 2616 for the definition of H(A1).
# "ERR" responses may optionally be followed by a error description
# available as %m in the returned error page.
#
# By default, the digest authentication scheme is not used unless a
# program is specified.
#
# If you want to use a digest authenticator, set this line to
# something like
#
# auth_param digest program /usr/lib/squid3/digest_pw_auth /usr/etc/digpass
#
# "utf8" on|off
# HTTP uses iso-latin-1 as characterset, while some authentication
# backends such as LDAP expects UTF-8. If this is set to on Squid will
# translate the HTTP iso-latin-1 charset to UTF-8 before sending the
# username & password to the helper.
#
# "children" numberofchildren
# The number of authenticator processes to spawn (no default).
# If you start too few Squid will have to wait for them to
# process a backlog of H(A1) calculations, slowing it down.
# When the H(A1) calculations are done via a (slow) network
# you are likely to need lots of authenticator processes.
# auth_param digest children 5
#
# "realm" realmstring
# Specifies the realm name which is to be reported to the
# client for the digest proxy authentication scheme (part of
# the text the user will see when prompted their username and
# password). There is no default.
# auth_param digest realm Squid proxy-caching web server
#
# "nonce_garbage_interval" timeinterval
# Specifies the interval that nonces that have been issued
# to client_agent's are checked for validity.
#
# "nonce_max_duration" timeinterval
# Specifies the maximum length of time a given nonce will be
# valid for.
#
# "nonce_max_count" number
# Specifies the maximum number of times a given nonce can be
# used.
#
# "nonce_strictness" on|off
# Determines if squid requires strict increment-by-1 behavior
# for nonce counts, or just incrementing (off - for use when
# useragents generate nonce counts that occasionally miss 1
# (ie, 1,2,4,6)). Default off.
#
# "check_nonce_count" on|off
# This directive if set to off can disable the nonce count check
# completely to work around buggy digest qop implementations in
# certain mainstream browser versions. Default on to check the
# nonce count to protect from authentication replay attacks.
#
# "post_workaround" on|off
# This is a workaround to certain buggy browsers who sends
# an incorrect request digest in POST requests when reusing
# the same nonce as acquired earlier on a GET request.
#
# === NTLM scheme options follow ===
#
# "program" cmdline
# Specify the command for the external NTLM authenticator.
# Such a program reads exchanged NTLMSSP packets with
# the browser via Squid until authentication is completed.
# If you use an NTLM authenticator, make sure you have 1 acl
# of type proxy_auth. By default, the NTLM authenticator_program
# is not used.
#
# auth_param ntlm program /usr/lib/squid3/ntlm_auth
#
# "children" numberofchildren
# The number of authenticator processes to spawn (no default).
# If you start too few Squid will have to wait for them to
# process a backlog of credential verifications, slowing it
# down. When credential verifications are done via a (slow)
# network you are likely to need lots of authenticator
# processes.
#
# auth_param ntlm children 5
#
# "keep_alive" on|off
# Whether to keep the connection open after the initial response where
# Squid tells the browser which schemes are supported by the proxy.
# Some browsers are known to present many login popups or to corrupt
# POST/PUT requests transfer if the connection is not closed.
# The default is currently OFF to avoid this, but may change.
#
# auth_param ntlm keep_alive on
#
# === Options for configuring the NEGOTIATE auth-scheme follow ===
#
# "program" cmdline
# Specify the command for the external Negotiate authenticator.
# This protocol is used in Microsoft Active-Directory enabled setups with
# the Microsoft Internet Explorer or Mozilla Firefox browsers.
# Its main purpose is to exchange credentials with the Squid proxy
# using the Kerberos mechanisms.
# If you use a Negotiate authenticator, make sure you have at least
# one acl of type proxy_auth active. By default, the negotiate
# authenticator_program is not used.
# The only supported program for this role is the ntlm_auth
# program distributed as part of Samba, version 4 or later.
#
# auth_param negotiate program /usr/lib/squid3/ntlm_auth --helper-protocol=gss-spnego
#
# "children" numberofchildren
# The number of authenticator processes to spawn (no default).
# If you start too few Squid will have to wait for them to
# process a backlog of credential verifications, slowing it
# down. When crendential verifications are done via a (slow)
# network you are likely to need lots of authenticator
# processes.
# auth_param negotiate children 5
#
# "keep_alive" on|off
# Whether to keep the connection open after the initial response where
# Squid tells the browser which schemes are supported by the proxy.
# Some browsers are known to present many login popups or to corrupt
# POST/PUT requests transfer if the connection is not closed.
# The default is currently OFF to avoid this, but may change.
#
# auth_param negotiate keep_alive on
#
#
# Examples:
#
##Recommended minimum configuration per scheme:
##auth_param negotiate program <uncomment and complete this line to activate>
##auth_param negotiate children 5
##auth_param negotiate keep_alive on
##
##auth_param ntlm program <uncomment and complete this line to activate>
##auth_param ntlm children 5
##auth_param ntlm keep_alive on
##
##auth_param digest program <uncomment and complete this line>
##auth_param digest children 5
##auth_param digest realm Squid proxy-caching web server
##auth_param digest nonce_garbage_interval 5 minutes
##auth_param digest nonce_max_duration 30 minutes
##auth_param digest nonce_max_count 50
##
##auth_param basic program <uncomment and complete this line>
##auth_param basic children 5
##auth_param basic realm Squid proxy-caching web server
##auth_param basic credentialsttl 2 hours
#Default:
# none
# TAG: authenticate_cache_garbage_interval
# The time period between garbage collection across the username cache.
# This is a tradeoff between memory utilization (long intervals - say
# 2 days) and CPU (short intervals - say 1 minute). Only change if you
# have good reason to.
#Default:
# authenticate_cache_garbage_interval 1 hour
# TAG: authenticate_ttl
# The time a user & their credentials stay in the logged in
# user cache since their last request. When the garbage
# interval passes, all user credentials that have passed their
# TTL are removed from memory.
#Default:
# authenticate_ttl 1 hour
# TAG: authenticate_ip_ttl
# If you use proxy authentication and the 'max_user_ip' ACL,
# this directive controls how long Squid remembers the IP
# addresses associated with each user. Use a small value
# (e.g., 60 seconds) if your users might change addresses
# quickly, as is the case with dialups. You might be safe
# using a larger value (e.g., 2 hours) in a corporate LAN
# environment with relatively static address assignments.
#Default:
# authenticate_ip_ttl 0 seconds
# ACCESS CONTROLS
# -----------------------------------------------------------------------------
# TAG: external_acl_type
# This option defines external acl classes using a helper program
# to look up the status
#
# external_acl_type name [options] FORMAT.. /path/to/helper [helper arguments..]
#
# Options:
#
# ttl=n TTL in seconds for cached results (defaults to 3600
# for 1 hour)
# negative_ttl=n
# TTL for cached negative lookups (default same
# as ttl)
# children=n Number of acl helper processes spawn to service
# external acl lookups of this type. (default 5)
# concurrency=n concurrency level per process. Only used with helpers
# capable of processing more than one query at a time.
# cache=n result cache size, 0 is unbounded (default)
# grace=n Percentage remaining of TTL where a refresh of a
# cached entry should be initiated without needing to
# wait for a new reply. (default 0 for no grace period)
# protocol=2.5 Compatibility mode for Squid-2.5 external acl helpers
# ipv4 / ipv6 IP-mode used to communicate to this helper.
# For compatability with older configurations and helpers
# the default is currently 'ipv4'.
#
# FORMAT specifications
#
# %LOGIN Authenticated user login name
# %EXT_USER Username from external acl
# %IDENT Ident user name
# %SRC Client IP
# %SRCPORT Client source port
# %URI Requested URI
# %DST Requested host
# %PROTO Requested protocol
# %PORT Requested port
# %PATH Requested URL path
# %METHOD Request method
# %MYADDR Squid interface address
# %MYPORT Squid http_port number
# %PATH Requested URL-path (including query-string if any)
# %USER_CERT SSL User certificate in PEM format
# %USER_CERTCHAIN SSL User certificate chain in PEM format
# %USER_CERT_xx SSL User certificate subject attribute xx
# %USER_CA_xx SSL User certificate issuer attribute xx
#
# %>{Header} HTTP request header "Header"
# %>{Hdr:member}
# HTTP request header "Hdr" list member "member"
# %>{Hdr:;member}
# HTTP request header list member using ; as
# list separator. ; can be any non-alphanumeric
# character.
#
# %<{Header} HTTP reply header "Header"
# %<{Hdr:member}
# HTTP reply header "Hdr" list member "member"
# %<{Hdr:;member}
# HTTP reply header list member using ; as
# list separator. ; can be any non-alphanumeric
# character.
#
# %% The percent sign. Useful for helpers which need
# an unchanging input format.
#
# In addition to the above, any string specified in the referencing
# acl will also be included in the helper request line, after the
# specified formats (see the "acl external" directive)
#
# The helper receives lines per the above format specification,
# and returns lines starting with OK or ERR indicating the validity
# of the request and optionally followed by additional keywords with
# more details.
#
# General result syntax:
#
# OK/ERR keyword=value ...
#
# Defined keywords:
#
# user= The users name (login)
# password= The users password (for login= cache_peer option)
# message= Message describing the reason. Available as %o
# in error pages
# tag= Apply a tag to a request (for both ERR and OK results)
# Only sets a tag, does not alter existing tags.
# log= String to be logged in access.log. Available as
# %ea in logformat specifications
#
# If protocol=3.0 (the default) then URL escaping is used to protect
# each value in both requests and responses.
#
# If using protocol=2.5 then all values need to be enclosed in quotes
# if they may contain whitespace, or the whitespace escaped using \.
# And quotes or \ characters within the keyword value must be \ escaped.
#
# When using the concurrency= option the protocol is changed by
# introducing a query channel tag infront of the request/response.
# The query channel tag is a number between 0 and concurrency-1.
#Default:
# none
# TAG: acl
# Defining an Access List
#
# Every access list definition must begin with an aclname and acltype,
# followed by either type-specific arguments or a quoted filename that
# they are read from.
#
# acl aclname acltype argument ...
# acl aclname acltype "file" ...
#
# When using "file", the file should contain one item per line.
#
# By default, regular expressions are CASE-SENSITIVE.
# To make them case-insensitive, use the -i option. To return case-sensitive
# use the +i option between patterns, or make a new ACL line without -i.
#
# Some acl types require suspending the current request in order
# to access some external data source.
# Those which do are marked with the tag [slow], those which
# don't are marked as [fast].
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl
# for further information
#
# ***** ACL TYPES AVAILABLE *****
#
# acl aclname src ip-address/netmask ... # clients IP address [fast]
# acl aclname src addr1-addr2/netmask ... # range of addresses [fast]
# acl aclname dst ip-address/netmask ... # URL host's IP address [slow]
# acl aclname myip ip-address/netmask ... # local socket IP address [fast]
#
# acl aclname arp mac-address ... (xx:xx:xx:xx:xx:xx notation)
# # The arp ACL requires the special configure option --enable-arp-acl.
# # Furthermore, the ARP ACL code is not portable to all operating systems.
# # It works on Linux, Solaris, Windows, FreeBSD, and some
# # other *BSD variants.
# # [fast]
# #
# # NOTE: Squid can only determine the MAC address for clients that are on
# # the same subnet. If the client is on a different subnet,
# # then Squid cannot find out its MAC address.
#
# acl aclname srcdomain .foo.com ...
# # reverse lookup, from client IP [slow]
# acl aclname dstdomain .foo.com ...
# # Destination server from URL [fast]
# acl aclname srcdom_regex [-i] \.foo\.com ...
# # regex matching client name [slow]
# acl aclname dstdom_regex [-i] \.foo\.com ...
# # regex matching server [fast]
# #
# # For dstdomain and dstdom_regex a reverse lookup is tried if a IP
# # based URL is used and no match is found. The name "none" is used
# # if the reverse lookup fails.
#
# acl aclname src_as number ...
# acl aclname dst_as number ...
# # [fast]
# # Except for access control, AS numbers can be used for
# # routing of requests to specific caches. Here's an
# # example for routing all requests for AS#1241 and only
# # those to mycache.mydomain.net:
# # acl asexample dst_as 1241
# # cache_peer_access mycache.mydomain.net allow asexample
# # cache_peer_access mycache_mydomain.net deny all
#
# acl aclname peername myPeer ...
# # [fast]
# # match against a named cache_peer entry
# # set unique name= on cache_peer lines for reliable use.
#
# acl aclname time [day-abbrevs] [h1:m1-h2:m2]
# # [fast]
# # day-abbrevs:
# # S - Sunday
# # M - Monday
# # T - Tuesday
# # W - Wednesday
# # H - Thursday
# # F - Friday
# # A - Saturday
# # h1:m1 must be less than h2:m2
#
# acl aclname url_regex [-i] ^http:// ...
# # regex matching on whole URL [fast]
# acl aclname urlpath_regex [-i] \.gif$ ...
# # regex matching on URL path [fast]
#
# acl aclname port 80 70 21 0-1024... # destination TCP port [fast]
# # ranges are alloed
# acl aclname myport 3128 ... # local socket TCP port [fast]
# acl aclname myportname 3128 ... # http(s)_port name [fast]
#
# acl aclname proto HTTP FTP ... # request protocol [fast]
#
# acl aclname method GET POST ... # HTTP request method [fast]
#
# acl aclname http_status 200 301 500- 400-403 ...
# # status code in reply [fast]
#
# acl aclname browser [-i] regexp ...
# # pattern match on User-Agent header (see also req_header below) [fast]
#
# acl aclname referer_regex [-i] regexp ...
# # pattern match on Referer header [fast]
# # Referer is highly unreliable, so use with care
#
# acl aclname ident username ...
# acl aclname ident_regex [-i] pattern ...
# # string match on ident output [slow]
# # use REQUIRED to accept any non-null ident.
#
# acl aclname proxy_auth [-i] username ...
# acl aclname proxy_auth_regex [-i] pattern ...
# # perform http authentication challenge to the client and match against
# # supplied credentials [slow]
# #
# # takes a list of allowed usernames.
# # use REQUIRED to accept any valid username.
# #
# # Will use proxy authentication in forward-proxy scenarios, and plain
# # http authenticaiton in reverse-proxy scenarios
# #
# # NOTE: when a Proxy-Authentication header is sent but it is not
# # needed during ACL checking the username is NOT logged
# # in access.log.
# #
# # NOTE: proxy_auth requires a EXTERNAL authentication program
# # to check username/password combinations (see
# # auth_param directive).
# #
# # NOTE: proxy_auth can't be used in a transparent/intercepting proxy
# # as the browser needs to be configured for using a proxy in order
# # to respond to proxy authentication.
#
# acl aclname snmp_community string ...
# # A community string to limit access to your SNMP Agent [fast]
# # Example:
# #
# # acl snmppublic snmp_community public
#
# acl aclname maxconn number
# # This will be matched when the client's IP address has
# # more than <number> TCP connections established. [fast]
# # NOTE: This only measures direct TCP links so X-Forwarded-For
# # indirect clients are not counted.
#
# acl aclname max_user_ip [-s] number
# # This will be matched when the user attempts to log in from more
# # than <number> different ip addresses. The authenticate_ip_ttl
# # parameter controls the timeout on the ip entries. [fast]
# # If -s is specified the limit is strict, denying browsing
# # from any further IP addresses until the ttl has expired. Without
# # -s Squid will just annoy the user by "randomly" denying requests.
# # (the counter is reset each time the limit is reached and a
# # request is denied)
# # NOTE: in acceleration mode or where there is mesh of child proxies,
# # clients may appear to come from multiple addresses if they are
# # going through proxy farms, so a limit of 1 may cause user problems.
#
# acl aclname req_mime_type [-i] mime-type ...
# # regex match against the mime type of the request generated
# # by the client. Can be used to detect file upload or some
# # types HTTP tunneling requests [fast]
# # NOTE: This does NOT match the reply. You cannot use this
# # to match the returned file type.
#
# acl aclname req_header header-name [-i] any\.regex\.here
# # regex match against any of the known request headers. May be
# # thought of as a superset of "browser", "referer" and "mime-type"
# # ACL [fast]
#
# acl aclname rep_mime_type [-i] mime-type ...
# # regex match against the mime type of the reply received by
# # squid. Can be used to detect file download or some
# # types HTTP tunneling requests. [fast]
# # NOTE: This has no effect in http_access rules. It only has
# # effect in rules that affect the reply data stream such as
# # http_reply_access.
#
# acl aclname rep_header header-name [-i] any\.regex\.here
# # regex match against any of the known reply headers. May be
# # thought of as a superset of "browser", "referer" and "mime-type"
# # ACLs [fast]
#
# acl aclname external class_name [arguments...]
# # external ACL lookup via a helper class defined by the
# # external_acl_type directive [slow]
#
# acl aclname user_cert attribute values...
# # match against attributes in a user SSL certificate
# # attribute is one of DN/C/O/CN/L/ST [fast]
#
# acl aclname ca_cert attribute values...
# # match against attributes a users issuing CA SSL certificate
# # attribute is one of DN/C/O/CN/L/ST [fast]
#
# acl aclname ext_user username ...
# acl aclname ext_user_regex [-i] pattern ...
# # string match on username returned by external acl helper [slow]
# # use REQUIRED to accept any non-null user name.
#
# acl aclname tag tagvalue ...
# # string match on tag returned by external acl helper [slow]
#
# Examples:
# acl macaddress arp 09:00:2b:23:45:67
# acl myexample dst_as 1241
# acl password proxy_auth REQUIRED
# acl fileupload req_mime_type -i ^multipart/form-data$
# acl javascript rep_mime_type -i ^application/x-javascript$
#
#Default:
# acl all src all
#
#
# Recommended minimum configuration:
#
acl manager proto cache_object
acl localhost src 127.0.0.1/32 ::1
acl lanhome src 192.168.1.0/255.255.255.0
acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1
# Example rule allowing access from your local networks.
# Adapt to list your (internal) IP networks from where browsing
# should be allowed
#acl localnet src 10.0.0.0/8 # RFC1918 possible internal network
#acl localnet src 172.16.0.0/12 # RFC1918 possible internal network
#acl localnet src 192.168.0.0/16 # RFC1918 possible internal network
#acl localnet src fc00::/7 # RFC 4193 local private network range
#acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines
acl SSL_ports port 443
acl Safe_ports port 80 # http
acl Safe_ports port 21 # ftp
acl Safe_ports port 443 # https
acl Safe_ports port 70 # gopher
acl Safe_ports port 210 # wais
acl Safe_ports port 1025-65535 # unregistered ports
acl Safe_ports port 280 # http-mgmt
acl Safe_ports port 488 # gss-http
acl Safe_ports port 591 # filemaker
acl Safe_ports port 777 # multiling http
acl CONNECT method CONNECT
# TAG: follow_x_forwarded_for
# Allowing or Denying the X-Forwarded-For header to be followed to
# find the original source of a request.
#
# Requests may pass through a chain of several other proxies
# before reaching us. The X-Forwarded-For header will contain a
# comma-separated list of the IP addresses in the chain, with the
# rightmost address being the most recent.
#
# If a request reaches us from a source that is allowed by this
# configuration item, then we consult the X-Forwarded-For header
# to see where that host received the request from. If the
# X-Forwarded-For header contains multiple addresses, we continue
# backtracking until we reach an address for which we are not allowed
# to follow the X-Forwarded-For header, or until we reach the first
# address in the list. For the purpose of ACL used in the
# follow_x_forwarded_for directive the src ACL type always matches
# the address we are testing and srcdomain matches its rDNS.
#
# The end result of this process is an IP address that we will
# refer to as the indirect client address. This address may
# be treated as the client address for access control, ICAP, delay
# pools and logging, depending on the acl_uses_indirect_client,
# icap_uses_indirect_client, delay_pool_uses_indirect_client and
# log_uses_indirect_client options.
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
# SECURITY CONSIDERATIONS:
#
# Any host for which we follow the X-Forwarded-For header
# can place incorrect information in the header, and Squid
# will use the incorrect information as if it were the
# source address of the request. This may enable remote
# hosts to bypass any access control restrictions that are
# based on the client's source addresses.
#
# For example:
#
# acl localhost src 127.0.0.1
# acl my_other_proxy srcdomain .proxy.example.com
# follow_x_forwarded_for allow localhost
# follow_x_forwarded_for allow my_other_proxy
#Default:
# follow_x_forwarded_for deny all
# TAG: acl_uses_indirect_client on|off
# Controls whether the indirect client address
# (see follow_x_forwarded_for) is used instead of the
# direct client address in acl matching.
#
# NOTE: maxconn ACL considers direct TCP links and indirect
# clients will always have zero. So no match.
#Default:
# acl_uses_indirect_client on
# TAG: delay_pool_uses_indirect_client on|off
# Controls whether the indirect client address
# (see follow_x_forwarded_for) is used instead of the
# direct client address in delay pools.
#Default:
# delay_pool_uses_indirect_client on
# TAG: log_uses_indirect_client on|off
# Controls whether the indirect client address
# (see follow_x_forwarded_for) is used instead of the
# direct client address in the access log.
#Default:
# log_uses_indirect_client on
# TAG: http_access
# Allowing or Denying access based on defined access lists
#
# Access to the HTTP port:
# http_access allow|deny [!]aclname ...
http_access allow lanhome
#
# NOTE on default values:
#
# If there are no "access" lines present, the default is to deny
# the request.
#
# If none of the "access" lines cause a match, the default is the
# opposite of the last line in the list. If the last line was
# deny, the default is allow. Conversely, if the last line
# is allow, the default will be deny. For these reasons, it is a
# good idea to have an "deny all" entry at the end of your access
# lists to avoid potential confusion.
#
# This clause supports both fast and slow acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
#Default:
# http_access deny all
#
#
# Recommended minimum Access Permission configuration:
#
# Only allow cachemgr access from localhost
http_access allow manager localhost
http_access deny manager
# Deny requests to certain unsafe ports
# http_access deny !Safe_ports
# Deny CONNECT to other than secure SSL ports
http_access deny CONNECT !SSL_ports
# We strongly recommend the following be uncommented to protect innocent
# web applications running on the proxy server who think the only
# one who can access services on "localhost" is a local user
#http_access deny to_localhost
#
# INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS
#
# Example rule allowing access from your local networks.
# Adapt localnet in the ACL section to list your (internal) IP networks
# from where browsing should be allowed
#http_access allow localnet
http_access allow localhost
# And finally deny all other access to this proxy
http_access deny all
# TAG: adapted_http_access
# Allowing or Denying access based on defined access lists
#
# Essentially identical to http_access, but runs after redirectors
# and ICAP/eCAP adaptation. Allowing access control based on their
# output.
#
# If not set then only http_access is used.
#Default:
# none
# TAG: http_reply_access
# Allow replies to client requests. This is complementary to http_access.
#
# http_reply_access allow|deny [!] aclname ...
#
# NOTE: if there are no access lines present, the default is to allow
# all replies
#
# If none of the access lines cause a match the opposite of the
# last line will apply. Thus it is good practice to end the rules
# with an "allow all" or "deny all" entry.
#
# This clause supports both fast and slow acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#Default:
# none
# TAG: icp_access
# Allowing or Denying access to the ICP port based on defined
# access lists
#
# icp_access allow|deny [!]aclname ...
#
# See http_access for details
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
## Allow ICP queries from local networks only
##icp_access allow localnet
##icp_access deny all
#Default:
# icp_access deny all
# TAG: htcp_access
# Allowing or Denying access to the HTCP port based on defined
# access lists
#
# htcp_access allow|deny [!]aclname ...
#
# See http_access for details
#
# NOTE: The default if no htcp_access lines are present is to
# deny all traffic. This default may cause problems with peers
# using the htcp or htcp-oldsquid options.
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
## Allow HTCP queries from local networks only
##htcp_access allow localnet
##htcp_access deny all
#Default:
# htcp_access deny all
# TAG: htcp_clr_access
# Allowing or Denying access to purge content using HTCP based
# on defined access lists
#
# htcp_clr_access allow|deny [!]aclname ...
#
# See http_access for details
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
## Allow HTCP CLR requests from trusted peers
#acl htcp_clr_peer src 172.16.1.2
#htcp_clr_access allow htcp_clr_peer
#Default:
# htcp_clr_access deny all
# TAG: miss_access
# Determins whether network access is permitted when satisfying a request.
#
# For example;
# to force your neighbors to use you as a sibling instead of
# a parent.
#
# acl localclients src 172.16.0.0/16
# miss_access allow localclients
# miss_access deny !localclients
#
# This means only your local clients are allowed to fetch relayed/MISS
# replies from the network and all other clients can only fetch cached
# objects (HITs).
#
#
# The default for this setting allows all clients who passed the
# http_access rules to relay via this proxy.
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#Default:
# miss_access allow all
# TAG: ident_lookup_access
# A list of ACL elements which, if matched, cause an ident
# (RFC 931) lookup to be performed for this request. For
# example, you might choose to always perform ident lookups
# for your main multi-user Unix boxes, but not for your Macs
# and PCs. By default, ident lookups are not performed for
# any requests.
#
# To enable ident lookups for specific client addresses, you
# can follow this example:
#
# acl ident_aware_hosts src 198.168.1.0/24
# ident_lookup_access allow ident_aware_hosts
# ident_lookup_access deny all
#
# Only src type ACL checks are fully supported. A srcdomain
# ACL might work at times, but it will not always provide
# the correct result.
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#Default:
# ident_lookup_access deny all
# TAG: reply_body_max_size size [acl acl...]
# This option specifies the maximum size of a reply body. It can be
# used to prevent users from downloading very large files, such as
# MP3's and movies. When the reply headers are received, the
# reply_body_max_size lines are processed, and the first line where
# all (if any) listed ACLs are true is used as the maximum body size
# for this reply.
#
# This size is checked twice. First when we get the reply headers,
# we check the content-length value. If the content length value exists
# and is larger than the allowed size, the request is denied and the
# user receives an error message that says "the request or reply
# is too large." If there is no content-length, and the reply
# size exceeds this limit, the client's connection is just closed
# and they will receive a partial reply.
#
# WARNING: downstream caches probably can not detect a partial reply
# if there is no content-length header, so they will cache
# partial responses and give them out as hits. You should NOT
# use this option if you have downstream caches.
#
# WARNING: A maximum size smaller than the size of squid's error messages
# will cause an infinite loop and crash squid. Ensure that the smallest
# non-zero value you use is greater that the maximum header size plus
# the size of your largest error page.
#
# If you set this parameter none (the default), there will be
# no limit imposed.
#
# Configuration Format is:
# reply_body_max_size SIZE UNITS [acl ...]
# ie.
# reply_body_max_size 10 MB
#
#Default:
# none
# NETWORK OPTIONS
# -----------------------------------------------------------------------------
# TAG: http_port
# Usage: port [options]
# hostname:port [options]
# 1.2.3.4:port [options]
#
# The socket addresses where Squid will listen for HTTP client
# requests. You may specify multiple socket addresses.
# There are three forms: port alone, hostname with port, and
# IP address with port. If you specify a hostname or IP
# address, Squid binds the socket to that specific
# address. This replaces the old 'tcp_incoming_address'
# option. Most likely, you do not need to bind to a specific
# address, so you can use the port number alone.
#
# If you are running Squid in accelerator mode, you
# probably want to listen on port 80 also, or instead.
#
# The -a command line option may be used to specify additional
# port(s) where Squid listens for proxy request. Such ports will
# be plain proxy ports with no options.
#
# You may specify multiple socket addresses on multiple lines.
#
# Options:
#
# intercept Support for IP-Layer interception of
# outgoing requests without browser settings.
# NP: disables authentication and IPv6 on the port.
#
# tproxy Support Linux TPROXY for spoofing outgoing
# connections using the client IP address.
# NP: disables authentication and maybe IPv6 on the port.
#
# accel Accelerator mode. Also needs at least one of
# vhost / vport / defaultsite.
#
# allow-direct Allow direct forwarding in accelerator mode. Normally
# accelerated requests are denied direct forwarding as if
# never_direct was used.
#
# defaultsite=domainname
# What to use for the Host: header if it is not present
# in a request. Determines what site (not origin server)
# accelerators should consider the default.
# Implies accel.
#
# vhost Accelerator mode using Host header for virtual domain support.
# Also uses the port as specified in Host: header unless
# overridden by the vport option. Implies accel.
#
# vport Virtual host port support. Using the http_port number
# instead of the port passed on Host: headers. Implies accel.
#
# vport=NN Virtual host port support. Using the specified port
# number instead of the port passed on Host: headers.
# Implies accel.
#
# protocol= Protocol to reconstruct accelerated requests with.
# Defaults to http.
#
# ignore-cc Ignore request Cache-Control headers.
#
# Warning: This option violates HTTP specifications if
# used in non-accelerator setups.
#
# connection-auth[=on|off]
# use connection-auth=off to tell Squid to prevent
# forwarding Microsoft connection oriented authentication
# (NTLM, Negotiate and Kerberos)
#
# disable-pmtu-discovery=
# Control Path-MTU discovery usage:
# off lets OS decide on what to do (default).
# transparent disable PMTU discovery when transparent
# support is enabled.
# always disable always PMTU discovery.
#
# In many setups of transparently intercepting proxies
# Path-MTU discovery can not work on traffic towards the
# clients. This is the case when the intercepting device
# does not fully track connections and fails to forward
# ICMP must fragment messages to the cache server. If you
# have such setup and experience that certain clients
# sporadically hang or never complete requests set
# disable-pmtu-discovery option to 'transparent'.
#
# ssl-bump Intercept each CONNECT request matching ssl_bump ACL,
# establish secure connection with the client and with
# the server, decrypt HTTP messages as they pass through
# Squid, and treat them as unencrypted HTTP messages,
# becoming the man-in-the-middle.
#
# When this option is enabled, additional options become
# available to specify SSL-related properties of the
# client-side connection: cert, key, version, cipher,
# options, clientca, cafile, capath, crlfile, dhparams,
# sslflags, and sslcontext. See the https_port directive
# for more information on these options.
#
# The ssl_bump option is required to fully enable
# the SslBump feature.
#
# name= Specifies a internal name for the port. Defaults to
# the port specification (port or addr:port)
#
# tcpkeepalive[=idle,interval,timeout]
# Enable TCP keepalive probes of idle connections.
# In seconds; idle is the initial time before TCP starts
# probing the connection, interval how often to probe, and
# timeout the time before giving up.
#
# If you run Squid on a dual-homed machine with an internal
# and an external interface we recommend you to specify the
# internal address:port in http_port. This way Squid will only be
# visible on the internal address.
#
#
# Squid normally listens to port 3128
http_port 3128
# TAG: https_port
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# Usage: [ip:]port cert=certificate.pem [key=key.pem] [options...]
#
# The socket address where Squid will listen for HTTPS client
# requests.
#
# This is really only useful for situations where you are running
# squid in accelerator mode and you want to do the SSL work at the
# accelerator level.
#
# You may specify multiple socket addresses on multiple lines,
# each with their own SSL certificate and/or options.
#
# Options:
#
# accel Accelerator mode. Also needs at least one of
# defaultsite or vhost.
#
# defaultsite= The name of the https site presented on
# this port. Implies accel.
#
# vhost Accelerator mode using Host header for virtual
# domain support. Requires a wildcard certificate
# or other certificate valid for more than one domain.
# Implies accel.
#
# protocol= Protocol to reconstruct accelerated requests with.
# Defaults to https.
#
# cert= Path to SSL certificate (PEM format).
#
# key= Path to SSL private key file (PEM format)
# if not specified, the certificate file is
# assumed to be a combined certificate and
# key file.
#
# version= The version of SSL/TLS supported
# 1 automatic (default)
# 2 SSLv2 only
# 3 SSLv3 only
# 4 TLSv1 only
#
# cipher= Colon separated list of supported ciphers.
# NOTE: some ciphers such as EDH ciphers depend on
# additional settings. If those settings are
# omitted the ciphers may be silently ignored
# by the OpenSSL library.
#
# options= Various SSL engine options. The most important
# being:
# NO_SSLv2 Disallow the use of SSLv2
# NO_SSLv3 Disallow the use of SSLv3
# NO_TLSv1 Disallow the use of TLSv1
# SINGLE_DH_USE Always create a new key when using
# temporary/ephemeral DH key exchanges
# See OpenSSL SSL_CTX_set_options documentation for a
# complete list of options.
#
# clientca= File containing the list of CAs to use when
# requesting a client certificate.
#
# cafile= File containing additional CA certificates to
# use when verifying client certificates. If unset
# clientca will be used.
#
# capath= Directory containing additional CA certificates
# and CRL lists to use when verifying client certificates.
#
# crlfile= File of additional CRL lists to use when verifying
# the client certificate, in addition to CRLs stored in
# the capath. Implies VERIFY_CRL flag below.
#
# dhparams= File containing DH parameters for temporary/ephemeral
# DH key exchanges. See OpenSSL documentation for details
# on how to create this file.
# WARNING: EDH ciphers will be silently disabled if this
# option is not set.
#
# sslflags= Various flags modifying the use of SSL:
# DELAYED_AUTH
# Don't request client certificates
# immediately, but wait until acl processing
# requires a certificate (not yet implemented).
# NO_DEFAULT_CA
# Don't use the default CA lists built in
# to OpenSSL.
# NO_SESSION_REUSE
# Don't allow for session reuse. Each connection
# will result in a new SSL session.
# VERIFY_CRL
# Verify CRL lists when accepting client
# certificates.
# VERIFY_CRL_ALL
# Verify CRL lists for all certificates in the
# client certificate chain.
#
# sslcontext= SSL session ID context identifier.
#
# generate-host-certificates[=<on|off>]
# Dynamically create SSL server certificates for the
# destination hosts of bumped CONNECT requests.When
# enabled, the cert and key options are used to sign
# generated certificates. Otherwise generated
# certificate will be selfsigned.
# If there is CA certificate life time of generated
# certificate equals lifetime of CA certificate. If
# generated certificate is selfsigned lifetime is three
# years.
# This option is enabled by default when SslBump is used.
# See the sslBump option above for more information.
#
# dynamic_cert_mem_cache_size=SIZE
# Approximate total RAM size spent on cached generated
# certificates. If set to zero, caching is disabled. The
# default value is 4MB. An average XXX-bit certificate
# consumes about XXX bytes of RAM.
#
# vport Accelerator with IP based virtual host support.
#
# vport=NN As above, but uses specified port number rather
# than the https_port number. Implies accel.
#
# name= Specifies a internal name for the port. Defaults to
# the port specification (port or addr:port)
#
#Default:
# none
# TAG: tcp_outgoing_tos
# Allows you to select a TOS/Diffserv value to mark outgoing
# connections with, based on the username or source address
# making the request.
#
# tcp_outgoing_tos ds-field [!]aclname ...
#
# Example where normal_service_net uses the TOS value 0x00
# and good_service_net uses 0x20
#
# acl normal_service_net src 10.0.0.0/24
# acl good_service_net src 10.0.1.0/24
# tcp_outgoing_tos 0x00 normal_service_net
# tcp_outgoing_tos 0x20 good_service_net
#
# TOS/DSCP values really only have local significance - so you should
# know what you're specifying. For more information, see RFC2474,
# RFC2475, and RFC3260.
#
# The TOS/DSCP byte must be exactly that - a octet value 0 - 255, or
# "default" to use whatever default your host has. Note that in
# practice often only multiples of 4 is usable as the two rightmost bits
# have been redefined for use by ECN (RFC 3168 section 23.1).
#
# Processing proceeds in the order specified, and stops at first fully
# matching line.
#
# Note: The use of this directive using client dependent ACLs is
# incompatible with the use of server side persistent connections. To
# ensure correct results it is best to set server_persisten_connections
# to off when using this directive in such configurations.
#Default:
# none
# TAG: clientside_tos
# Allows you to select a TOS/Diffserv value to mark client-side
# connections with, based on the username or source address
# making the request.
#Default:
# none
# TAG: qos_flows
# Allows you to select a TOS/DSCP value to mark outgoing
# connections with, based on where the reply was sourced.
#
# TOS values really only have local significance - so you should
# know what you're specifying. For more information, see RFC2474,
# RFC2475, and RFC3260.
#
# The TOS/DSCP byte must be exactly that - octet value 0x00-0xFF.
# Note that in practice often only values up to 0x3F are usable
# as the two highest bits have been redefined for use by ECN
# (RFC3168).
#
# This setting is configured by setting the source TOS values:
#
# local-hit=0xFF Value to mark local cache hits.
#
# sibling-hit=0xFF Value to mark hits from sibling peers.
#
# parent-hit=0xFF Value to mark hits from parent peers.
#
#
# NOTE: 'miss' preserve feature is only possible on Linux at this time.
#
# For the following to work correctly, you will need to patch your
# linux kernel with the TOS preserving ZPH patch.
# The kernel patch can be downloaded from http://zph.bratcheda.org
#
# disable-preserve-miss
# By default, the existing TOS value of the response coming
# from the remote server will be retained and masked with
# miss-mark. This option disables that feature.
#
# miss-mask=0xFF
# Allows you to mask certain bits in the TOS received from the
# remote server, before copying the value to the TOS sent
# towards clients.
# Default: 0xFF (TOS from server is not changed).
#
#Default:
# none
# TAG: tcp_outgoing_address
# Allows you to map requests to different outgoing IP addresses
# based on the username or source address of the user making
# the request.
#
# tcp_outgoing_address ipaddr [[!]aclname] ...
#
# Example where requests from 10.0.0.0/24 will be forwarded
# with source address 10.1.0.1, 10.0.2.0/24 forwarded with
# source address 10.1.0.2 and the rest will be forwarded with
# source address 10.1.0.3.
#
# acl normal_service_net src 10.0.0.0/24
# acl good_service_net src 10.0.2.0/24
# tcp_outgoing_address 10.1.0.1 normal_service_net
# tcp_outgoing_address 10.1.0.2 good_service_net
# tcp_outgoing_address 10.1.0.3
#
# Processing proceeds in the order specified, and stops at first fully
# matching line.
#
# Note: The use of this directive using client dependent ACLs is
# incompatible with the use of server side persistent connections. To
# ensure correct results it is best to set server_persistent_connections
# to off when using this directive in such configurations.
#
#
# IPv6 Magic:
#
# Squid is built with a capability of bridging the IPv4 and IPv6
# internets.
# tcp_outgoing_address as exampled above breaks this bridging by forcing
# all outbound traffic through a certain IPv4 which may be on the wrong
# side of the IPv4/IPv6 boundary.
#
# To operate with tcp_outgoing_address and keep the bridging benefits
# an additional ACL needs to be used which ensures the IPv6-bound traffic
# is never forced or permitted out the IPv4 interface.
#
# # IPv6 destination test along with a dummy access control to perofrm the required DNS
# # This MUST be place before any ALLOW rules.
# acl to_ipv6 dst ipv6
# http_access deny ipv6 !all
#
# tcp_outgoing_address 2001:db8::c001 good_service_net to_ipv6
# tcp_outgoing_address 10.1.0.2 good_service_net !to_ipv6
#
# tcp_outgoing_address 2001:db8::beef normal_service_net to_ipv6
# tcp_outgoing_address 10.1.0.1 normal_service_net !to_ipv6
#
# tcp_outgoing_address 2001:db8::1 to_ipv6
# tcp_outgoing_address 10.1.0.3 !to_ipv6
#
# WARNING:
# 'dst ipv6' bases its selection assuming DIRECT access.
# If peers are used the peername ACL are needed to select outgoing
# address which can link to the peer.
#
# 'dst ipv6' is a slow ACL. It will only work here if 'dst' is used
# previously in the http_access rules to locate the destination IP.
# Some more magic may be needed for that:
# http_access allow to_ipv6 !all
# (meaning, allow if to IPv6 but not from anywhere ;)
#
#Default:
# none
# SSL OPTIONS
# -----------------------------------------------------------------------------
# TAG: ssl_unclean_shutdown
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# Some browsers (especially MSIE) bugs out on SSL shutdown
# messages.
#Default:
# ssl_unclean_shutdown off
# TAG: ssl_engine
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# The OpenSSL engine to use. You will need to set this if you
# would like to use hardware SSL acceleration for example.
#Default:
# none
# TAG: sslproxy_client_certificate
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# Client SSL Certificate to use when proxying https:// URLs
#Default:
# none
# TAG: sslproxy_client_key
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# Client SSL Key to use when proxying https:// URLs
#Default:
# none
# TAG: sslproxy_version
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# SSL version level to use when proxying https:// URLs
#Default:
# sslproxy_version 1
# TAG: sslproxy_options
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# SSL engine options to use when proxying https:// URLs
#
# The most important being:
#
# NO_SSLv2 Disallow the use of SSLv2
# NO_SSLv3 Disallow the use of SSLv3
# NO_TLSv1 Disallow the use of TLSv1
# SINGLE_DH_USE
# Always create a new key when using
# temporary/ephemeral DH key exchanges
#
# These options vary depending on your SSL engine.
# See the OpenSSL SSL_CTX_set_options documentation for a
# complete list of possible options.
#Default
# ----------------------------
#
# This is the documentation for the Squid configuration file.
# This documentation can also be found online at:
# http://www.squid-cache.org/Doc/config/
#
# You may wish to look at the Squid home page and wiki for the
# FAQ and other documentation:
# http://www.squid-cache.org/
# http://wiki.squid-cache.org/SquidFaq
# http://wiki.squid-cache.org/ConfigExamples
#
# This documentation shows what the defaults for various directives
# happen to be. If you don't need to change the default, you should
# leave the line out of your squid.conf in most cases.
#
# In some cases "none" refers to no default setting at all,
# while in other cases it refers to the value of the option
# - the comments for that keyword indicate if this is the case.
#
# Configuration options can be included using the "include" directive.
# Include takes a list of files to include. Quoting and wildcards are
# supported.
#
# For example,
#
# include /path/to/included/file/squid.acl.config
#
# Includes can be nested up to a hard-coded depth of 16 levels.
# This arbitrary restriction is to prevent recursive include references
# from causing Squid entering an infinite loop whilst trying to load
# configuration files.
# TAG: dns_testnames
# Remove this line. DNS is no longer tested on startup.
#Default:
# none
# TAG: extension_methods
# Remove this line. All valid methods for HTTP are accepted by default.
#Default:
# none
# TAG: incoming_rate
#Default:
# none
# TAG: server_http11
# Remove this line. HTTP/1.1 is supported by default.
#Default:
# none
# TAG: upgrade_http0.9
# Remove this line. ICY/1.0 streaming protocol is supported by default.
#Default:
# none
# TAG: zph_local
# Alter these entries. Use the qos_flows directive instead.
#Default:
# none
# TAG: header_access
# Since squid-3.0 replace with request_header_access or reply_header_access
# depending on whether you wish to match client requests or server replies.
#Default:
# none
# TAG: httpd_accel_no_pmtu_disc
# Since squid-3.0 use the 'disable-pmtu-discovery' flag on http_port instead.
#Default:
# none
# OPTIONS FOR AUTHENTICATION
# -----------------------------------------------------------------------------
# TAG: auth_param
# This is used to define parameters for the various authentication
# schemes supported by Squid.
#
# format: auth_param scheme parameter [setting]
#
# The order in which authentication schemes are presented to the client is
# dependent on the order the scheme first appears in config file. IE
# has a bug (it's not RFC 2617 compliant) in that it will use the basic
# scheme if basic is the first entry presented, even if more secure
# schemes are presented. For now use the order in the recommended
# settings section below. If other browsers have difficulties (don't
# recognize the schemes offered even if you are using basic) either
# put basic first, or disable the other schemes (by commenting out their
# program entry).
#
# Once an authentication scheme is fully configured, it can only be
# shutdown by shutting squid down and restarting. Changes can be made on
# the fly and activated with a reconfigure. I.E. You can change to a
# different helper, but not unconfigure the helper completely.
#
# Please note that while this directive defines how Squid processes
# authentication it does not automatically activate authentication.
# To use authentication you must in addition make use of ACLs based
# on login name in http_access (proxy_auth, proxy_auth_regex or
# external with %LOGIN used in the format tag). The browser will be
# challenged for authentication on the first such acl encountered
# in http_access processing and will also be re-challenged for new
# login credentials if the request is being denied by a proxy_auth
# type acl.
#
# WARNING: authentication can't be used in a transparently intercepting
# proxy as the client then thinks it is talking to an origin server and
# not the proxy. This is a limitation of bending the TCP/IP protocol to
# transparently intercepting port 80, not a limitation in Squid.
# Ports flagged 'transparent', 'intercept', or 'tproxy' have
# authentication disabled.
#
# === Parameters for the basic scheme follow. ===
#
# "program" cmdline
# Specify the command for the external authenticator. Such a program
# reads a line containing "username password" and replies "OK" or
# "ERR" in an endless loop. "ERR" responses may optionally be followed
# by a error description available as %m in the returned error page.
# If you use an authenticator, make sure you have 1 acl of type
# proxy_auth.
#
# By default, the basic authentication scheme is not used unless a
# program is specified.
#
# If you want to use the traditional NCSA proxy authentication, set
# this line to something like
#
# auth_param basic program /usr/lib/squid3/ncsa_auth /usr/etc/passwd
#
# "utf8" on|off
# HTTP uses iso-latin-1 as characterset, while some authentication
# backends such as LDAP expects UTF-8. If this is set to on Squid will
# translate the HTTP iso-latin-1 charset to UTF-8 before sending the
# username & password to the helper.
#
# "children" numberofchildren
# The number of authenticator processes to spawn. If you start too few
# Squid will have to wait for them to process a backlog of credential
# verifications, slowing it down. When password verifications are
# done via a (slow) network you are likely to need lots of
# authenticator processes.
# auth_param basic children 5
#
# "concurrency" concurrency
# The number of concurrent requests the helper can process.
# The default of 0 is used for helpers who only supports
# one request at a time. Setting this changes the protocol used to
# include a channel number first on the request/response line, allowing
# multiple requests to be sent to the same helper in parallell without
# wating for the response.
# Must not be set unless it's known the helper supports this.
# auth_param basic concurrency 0
#
# "realm" realmstring
# Specifies the realm name which is to be reported to the
# client for the basic proxy authentication scheme (part of
# the text the user will see when prompted their username and
# password). There is no default.
# auth_param basic realm Squid proxy-caching web server
#
# "credentialsttl" timetolive
# Specifies how long squid assumes an externally validated
# username:password pair is valid for - in other words how
# often the helper program is called for that user. Set this
# low to force revalidation with short lived passwords. Note
# setting this high does not impact your susceptibility
# to replay attacks unless you are using an one-time password
# system (such as SecureID). If you are using such a system,
# you will be vulnerable to replay attacks unless you also
# use the max_user_ip ACL in an http_access rule.
#
# "casesensitive" on|off
# Specifies if usernames are case sensitive. Most user databases are
# case insensitive allowing the same username to be spelled using both
# lower and upper case letters, but some are case sensitive. This
# makes a big difference for user_max_ip ACL processing and similar.
# auth_param basic casesensitive off
#
# === Parameters for the digest scheme follow ===
#
# "program" cmdline
# Specify the command for the external authenticator. Such
# a program reads a line containing "username":"realm" and
# replies with the appropriate H(A1) value hex encoded or
# ERR if the user (or his H(A1) hash) does not exists.
# See rfc 2616 for the definition of H(A1).
# "ERR" responses may optionally be followed by a error description
# available as %m in the returned error page.
#
# By default, the digest authentication scheme is not used unless a
# program is specified.
#
# If you want to use a digest authenticator, set this line to
# something like
#
# auth_param digest program /usr/lib/squid3/digest_pw_auth /usr/etc/digpass
#
# "utf8" on|off
# HTTP uses iso-latin-1 as characterset, while some authentication
# backends such as LDAP expects UTF-8. If this is set to on Squid will
# translate the HTTP iso-latin-1 charset to UTF-8 before sending the
# username & password to the helper.
#
# "children" numberofchildren
# The number of authenticator processes to spawn (no default).
# If you start too few Squid will have to wait for them to
# process a backlog of H(A1) calculations, slowing it down.
# When the H(A1) calculations are done via a (slow) network
# you are likely to need lots of authenticator processes.
# auth_param digest children 5
#
# "realm" realmstring
# Specifies the realm name which is to be reported to the
# client for the digest proxy authentication scheme (part of
# the text the user will see when prompted their username and
# password). There is no default.
# auth_param digest realm Squid proxy-caching web server
#
# "nonce_garbage_interval" timeinterval
# Specifies the interval that nonces that have been issued
# to client_agent's are checked for validity.
#
# "nonce_max_duration" timeinterval
# Specifies the maximum length of time a given nonce will be
# valid for.
#
# "nonce_max_count" number
# Specifies the maximum number of times a given nonce can be
# used.
#
# "nonce_strictness" on|off
# Determines if squid requires strict increment-by-1 behavior
# for nonce counts, or just incrementing (off - for use when
# useragents generate nonce counts that occasionally miss 1
# (ie, 1,2,4,6)). Default off.
#
# "check_nonce_count" on|off
# This directive if set to off can disable the nonce count check
# completely to work around buggy digest qop implementations in
# certain mainstream browser versions. Default on to check the
# nonce count to protect from authentication replay attacks.
#
# "post_workaround" on|off
# This is a workaround to certain buggy browsers who sends
# an incorrect request digest in POST requests when reusing
# the same nonce as acquired earlier on a GET request.
#
# === NTLM scheme options follow ===
#
# "program" cmdline
# Specify the command for the external NTLM authenticator.
# Such a program reads exchanged NTLMSSP packets with
# the browser via Squid until authentication is completed.
# If you use an NTLM authenticator, make sure you have 1 acl
# of type proxy_auth. By default, the NTLM authenticator_program
# is not used.
#
# auth_param ntlm program /usr/lib/squid3/ntlm_auth
#
# "children" numberofchildren
# The number of authenticator processes to spawn (no default).
# If you start too few Squid will have to wait for them to
# process a backlog of credential verifications, slowing it
# down. When credential verifications are done via a (slow)
# network you are likely to need lots of authenticator
# processes.
#
# auth_param ntlm children 5
#
# "keep_alive" on|off
# Whether to keep the connection open after the initial response where
# Squid tells the browser which schemes are supported by the proxy.
# Some browsers are known to present many login popups or to corrupt
# POST/PUT requests transfer if the connection is not closed.
# The default is currently OFF to avoid this, but may change.
#
# auth_param ntlm keep_alive on
#
# === Options for configuring the NEGOTIATE auth-scheme follow ===
#
# "program" cmdline
# Specify the command for the external Negotiate authenticator.
# This protocol is used in Microsoft Active-Directory enabled setups with
# the Microsoft Internet Explorer or Mozilla Firefox browsers.
# Its main purpose is to exchange credentials with the Squid proxy
# using the Kerberos mechanisms.
# If you use a Negotiate authenticator, make sure you have at least
# one acl of type proxy_auth active. By default, the negotiate
# authenticator_program is not used.
# The only supported program for this role is the ntlm_auth
# program distributed as part of Samba, version 4 or later.
#
# auth_param negotiate program /usr/lib/squid3/ntlm_auth --helper-protocol=gss-spnego
#
# "children" numberofchildren
# The number of authenticator processes to spawn (no default).
# If you start too few Squid will have to wait for them to
# process a backlog of credential verifications, slowing it
# down. When crendential verifications are done via a (slow)
# network you are likely to need lots of authenticator
# processes.
# auth_param negotiate children 5
#
# "keep_alive" on|off
# Whether to keep the connection open after the initial response where
# Squid tells the browser which schemes are supported by the proxy.
# Some browsers are known to present many login popups or to corrupt
# POST/PUT requests transfer if the connection is not closed.
# The default is currently OFF to avoid this, but may change.
#
# auth_param negotiate keep_alive on
#
#
# Examples:
#
##Recommended minimum configuration per scheme:
##auth_param negotiate program <uncomment and complete this line to activate>
##auth_param negotiate children 5
##auth_param negotiate keep_alive on
##
##auth_param ntlm program <uncomment and complete this line to activate>
##auth_param ntlm children 5
##auth_param ntlm keep_alive on
##
##auth_param digest program <uncomment and complete this line>
##auth_param digest children 5
##auth_param digest realm Squid proxy-caching web server
##auth_param digest nonce_garbage_interval 5 minutes
##auth_param digest nonce_max_duration 30 minutes
##auth_param digest nonce_max_count 50
##
##auth_param basic program <uncomment and complete this line>
##auth_param basic children 5
##auth_param basic realm Squid proxy-caching web server
##auth_param basic credentialsttl 2 hours
#Default:
# none
# TAG: authenticate_cache_garbage_interval
# The time period between garbage collection across the username cache.
# This is a tradeoff between memory utilization (long intervals - say
# 2 days) and CPU (short intervals - say 1 minute). Only change if you
# have good reason to.
#Default:
# authenticate_cache_garbage_interval 1 hour
# TAG: authenticate_ttl
# The time a user & their credentials stay in the logged in
# user cache since their last request. When the garbage
# interval passes, all user credentials that have passed their
# TTL are removed from memory.
#Default:
# authenticate_ttl 1 hour
# TAG: authenticate_ip_ttl
# If you use proxy authentication and the 'max_user_ip' ACL,
# this directive controls how long Squid remembers the IP
# addresses associated with each user. Use a small value
# (e.g., 60 seconds) if your users might change addresses
# quickly, as is the case with dialups. You might be safe
# using a larger value (e.g., 2 hours) in a corporate LAN
# environment with relatively static address assignments.
#Default:
# authenticate_ip_ttl 0 seconds
# ACCESS CONTROLS
# -----------------------------------------------------------------------------
# TAG: external_acl_type
# This option defines external acl classes using a helper program
# to look up the status
#
# external_acl_type name [options] FORMAT.. /path/to/helper [helper arguments..]
#
# Options:
#
# ttl=n TTL in seconds for cached results (defaults to 3600
# for 1 hour)
# negative_ttl=n
# TTL for cached negative lookups (default same
# as ttl)
# children=n Number of acl helper processes spawn to service
# external acl lookups of this type. (default 5)
# concurrency=n concurrency level per process. Only used with helpers
# capable of processing more than one query at a time.
# cache=n result cache size, 0 is unbounded (default)
# grace=n Percentage remaining of TTL where a refresh of a
# cached entry should be initiated without needing to
# wait for a new reply. (default 0 for no grace period)
# protocol=2.5 Compatibility mode for Squid-2.5 external acl helpers
# ipv4 / ipv6 IP-mode used to communicate to this helper.
# For compatability with older configurations and helpers
# the default is currently 'ipv4'.
#
# FORMAT specifications
#
# %LOGIN Authenticated user login name
# %EXT_USER Username from external acl
# %IDENT Ident user name
# %SRC Client IP
# %SRCPORT Client source port
# %URI Requested URI
# %DST Requested host
# %PROTO Requested protocol
# %PORT Requested port
# %PATH Requested URL path
# %METHOD Request method
# %MYADDR Squid interface address
# %MYPORT Squid http_port number
# %PATH Requested URL-path (including query-string if any)
# %USER_CERT SSL User certificate in PEM format
# %USER_CERTCHAIN SSL User certificate chain in PEM format
# %USER_CERT_xx SSL User certificate subject attribute xx
# %USER_CA_xx SSL User certificate issuer attribute xx
#
# %>{Header} HTTP request header "Header"
# %>{Hdr:member}
# HTTP request header "Hdr" list member "member"
# %>{Hdr:;member}
# HTTP request header list member using ; as
# list separator. ; can be any non-alphanumeric
# character.
#
# %<{Header} HTTP reply header "Header"
# %<{Hdr:member}
# HTTP reply header "Hdr" list member "member"
# %<{Hdr:;member}
# HTTP reply header list member using ; as
# list separator. ; can be any non-alphanumeric
# character.
#
# %% The percent sign. Useful for helpers which need
# an unchanging input format.
#
# In addition to the above, any string specified in the referencing
# acl will also be included in the helper request line, after the
# specified formats (see the "acl external" directive)
#
# The helper receives lines per the above format specification,
# and returns lines starting with OK or ERR indicating the validity
# of the request and optionally followed by additional keywords with
# more details.
#
# General result syntax:
#
# OK/ERR keyword=value ...
#
# Defined keywords:
#
# user= The users name (login)
# password= The users password (for login= cache_peer option)
# message= Message describing the reason. Available as %o
# in error pages
# tag= Apply a tag to a request (for both ERR and OK results)
# Only sets a tag, does not alter existing tags.
# log= String to be logged in access.log. Available as
# %ea in logformat specifications
#
# If protocol=3.0 (the default) then URL escaping is used to protect
# each value in both requests and responses.
#
# If using protocol=2.5 then all values need to be enclosed in quotes
# if they may contain whitespace, or the whitespace escaped using \.
# And quotes or \ characters within the keyword value must be \ escaped.
#
# When using the concurrency= option the protocol is changed by
# introducing a query channel tag infront of the request/response.
# The query channel tag is a number between 0 and concurrency-1.
#Default:
# none
# TAG: acl
# Defining an Access List
#
# Every access list definition must begin with an aclname and acltype,
# followed by either type-specific arguments or a quoted filename that
# they are read from.
#
# acl aclname acltype argument ...
# acl aclname acltype "file" ...
#
# When using "file", the file should contain one item per line.
#
# By default, regular expressions are CASE-SENSITIVE.
# To make them case-insensitive, use the -i option. To return case-sensitive
# use the +i option between patterns, or make a new ACL line without -i.
#
# Some acl types require suspending the current request in order
# to access some external data source.
# Those which do are marked with the tag [slow], those which
# don't are marked as [fast].
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl
# for further information
#
# ***** ACL TYPES AVAILABLE *****
#
# acl aclname src ip-address/netmask ... # clients IP address [fast]
# acl aclname src addr1-addr2/netmask ... # range of addresses [fast]
# acl aclname dst ip-address/netmask ... # URL host's IP address [slow]
# acl aclname myip ip-address/netmask ... # local socket IP address [fast]
#
# acl aclname arp mac-address ... (xx:xx:xx:xx:xx:xx notation)
# # The arp ACL requires the special configure option --enable-arp-acl.
# # Furthermore, the ARP ACL code is not portable to all operating systems.
# # It works on Linux, Solaris, Windows, FreeBSD, and some
# # other *BSD variants.
# # [fast]
# #
# # NOTE: Squid can only determine the MAC address for clients that are on
# # the same subnet. If the client is on a different subnet,
# # then Squid cannot find out its MAC address.
#
# acl aclname srcdomain .foo.com ...
# # reverse lookup, from client IP [slow]
# acl aclname dstdomain .foo.com ...
# # Destination server from URL [fast]
# acl aclname srcdom_regex [-i] \.foo\.com ...
# # regex matching client name [slow]
# acl aclname dstdom_regex [-i] \.foo\.com ...
# # regex matching server [fast]
# #
# # For dstdomain and dstdom_regex a reverse lookup is tried if a IP
# # based URL is used and no match is found. The name "none" is used
# # if the reverse lookup fails.
#
# acl aclname src_as number ...
# acl aclname dst_as number ...
# # [fast]
# # Except for access control, AS numbers can be used for
# # routing of requests to specific caches. Here's an
# # example for routing all requests for AS#1241 and only
# # those to mycache.mydomain.net:
# # acl asexample dst_as 1241
# # cache_peer_access mycache.mydomain.net allow asexample
# # cache_peer_access mycache_mydomain.net deny all
#
# acl aclname peername myPeer ...
# # [fast]
# # match against a named cache_peer entry
# # set unique name= on cache_peer lines for reliable use.
#
# acl aclname time [day-abbrevs] [h1:m1-h2:m2]
# # [fast]
# # day-abbrevs:
# # S - Sunday
# # M - Monday
# # T - Tuesday
# # W - Wednesday
# # H - Thursday
# # F - Friday
# # A - Saturday
# # h1:m1 must be less than h2:m2
#
# acl aclname url_regex [-i] ^http:// ...
# # regex matching on whole URL [fast]
# acl aclname urlpath_regex [-i] \.gif$ ...
# # regex matching on URL path [fast]
#
# acl aclname port 80 70 21 0-1024... # destination TCP port [fast]
# # ranges are alloed
# acl aclname myport 3128 ... # local socket TCP port [fast]
# acl aclname myportname 3128 ... # http(s)_port name [fast]
#
# acl aclname proto HTTP FTP ... # request protocol [fast]
#
# acl aclname method GET POST ... # HTTP request method [fast]
#
# acl aclname http_status 200 301 500- 400-403 ...
# # status code in reply [fast]
#
# acl aclname browser [-i] regexp ...
# # pattern match on User-Agent header (see also req_header below) [fast]
#
# acl aclname referer_regex [-i] regexp ...
# # pattern match on Referer header [fast]
# # Referer is highly unreliable, so use with care
#
# acl aclname ident username ...
# acl aclname ident_regex [-i] pattern ...
# # string match on ident output [slow]
# # use REQUIRED to accept any non-null ident.
#
# acl aclname proxy_auth [-i] username ...
# acl aclname proxy_auth_regex [-i] pattern ...
# # perform http authentication challenge to the client and match against
# # supplied credentials [slow]
# #
# # takes a list of allowed usernames.
# # use REQUIRED to accept any valid username.
# #
# # Will use proxy authentication in forward-proxy scenarios, and plain
# # http authenticaiton in reverse-proxy scenarios
# #
# # NOTE: when a Proxy-Authentication header is sent but it is not
# # needed during ACL checking the username is NOT logged
# # in access.log.
# #
# # NOTE: proxy_auth requires a EXTERNAL authentication program
# # to check username/password combinations (see
# # auth_param directive).
# #
# # NOTE: proxy_auth can't be used in a transparent/intercepting proxy
# # as the browser needs to be configured for using a proxy in order
# # to respond to proxy authentication.
#
# acl aclname snmp_community string ...
# # A community string to limit access to your SNMP Agent [fast]
# # Example:
# #
# # acl snmppublic snmp_community public
#
# acl aclname maxconn number
# # This will be matched when the client's IP address has
# # more than <number> TCP connections established. [fast]
# # NOTE: This only measures direct TCP links so X-Forwarded-For
# # indirect clients are not counted.
#
# acl aclname max_user_ip [-s] number
# # This will be matched when the user attempts to log in from more
# # than <number> different ip addresses. The authenticate_ip_ttl
# # parameter controls the timeout on the ip entries. [fast]
# # If -s is specified the limit is strict, denying browsing
# # from any further IP addresses until the ttl has expired. Without
# # -s Squid will just annoy the user by "randomly" denying requests.
# # (the counter is reset each time the limit is reached and a
# # request is denied)
# # NOTE: in acceleration mode or where there is mesh of child proxies,
# # clients may appear to come from multiple addresses if they are
# # going through proxy farms, so a limit of 1 may cause user problems.
#
# acl aclname req_mime_type [-i] mime-type ...
# # regex match against the mime type of the request generated
# # by the client. Can be used to detect file upload or some
# # types HTTP tunneling requests [fast]
# # NOTE: This does NOT match the reply. You cannot use this
# # to match the returned file type.
#
# acl aclname req_header header-name [-i] any\.regex\.here
# # regex match against any of the known request headers. May be
# # thought of as a superset of "browser", "referer" and "mime-type"
# # ACL [fast]
#
# acl aclname rep_mime_type [-i] mime-type ...
# # regex match against the mime type of the reply received by
# # squid. Can be used to detect file download or some
# # types HTTP tunneling requests. [fast]
# # NOTE: This has no effect in http_access rules. It only has
# # effect in rules that affect the reply data stream such as
# # http_reply_access.
#
# acl aclname rep_header header-name [-i] any\.regex\.here
# # regex match against any of the known reply headers. May be
# # thought of as a superset of "browser", "referer" and "mime-type"
# # ACLs [fast]
#
# acl aclname external class_name [arguments...]
# # external ACL lookup via a helper class defined by the
# # external_acl_type directive [slow]
#
# acl aclname user_cert attribute values...
# # match against attributes in a user SSL certificate
# # attribute is one of DN/C/O/CN/L/ST [fast]
#
# acl aclname ca_cert attribute values...
# # match against attributes a users issuing CA SSL certificate
# # attribute is one of DN/C/O/CN/L/ST [fast]
#
# acl aclname ext_user username ...
# acl aclname ext_user_regex [-i] pattern ...
# # string match on username returned by external acl helper [slow]
# # use REQUIRED to accept any non-null user name.
#
# acl aclname tag tagvalue ...
# # string match on tag returned by external acl helper [slow]
#
# Examples:
# acl macaddress arp 09:00:2b:23:45:67
# acl myexample dst_as 1241
# acl password proxy_auth REQUIRED
# acl fileupload req_mime_type -i ^multipart/form-data$
# acl javascript rep_mime_type -i ^application/x-javascript$
#
#Default:
# acl all src all
#
#
# Recommended minimum configuration:
#
acl manager proto cache_object
acl localhost src 127.0.0.1/32 ::1
acl lanhome src 192.168.1.0/255.255.255.0
acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1
# Example rule allowing access from your local networks.
# Adapt to list your (internal) IP networks from where browsing
# should be allowed
#acl localnet src 10.0.0.0/8 # RFC1918 possible internal network
#acl localnet src 172.16.0.0/12 # RFC1918 possible internal network
#acl localnet src 192.168.0.0/16 # RFC1918 possible internal network
#acl localnet src fc00::/7 # RFC 4193 local private network range
#acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines
acl SSL_ports port 443
acl Safe_ports port 80 # http
acl Safe_ports port 21 # ftp
acl Safe_ports port 443 # https
acl Safe_ports port 70 # gopher
acl Safe_ports port 210 # wais
acl Safe_ports port 1025-65535 # unregistered ports
acl Safe_ports port 280 # http-mgmt
acl Safe_ports port 488 # gss-http
acl Safe_ports port 591 # filemaker
acl Safe_ports port 777 # multiling http
acl CONNECT method CONNECT
# TAG: follow_x_forwarded_for
# Allowing or Denying the X-Forwarded-For header to be followed to
# find the original source of a request.
#
# Requests may pass through a chain of several other proxies
# before reaching us. The X-Forwarded-For header will contain a
# comma-separated list of the IP addresses in the chain, with the
# rightmost address being the most recent.
#
# If a request reaches us from a source that is allowed by this
# configuration item, then we consult the X-Forwarded-For header
# to see where that host received the request from. If the
# X-Forwarded-For header contains multiple addresses, we continue
# backtracking until we reach an address for which we are not allowed
# to follow the X-Forwarded-For header, or until we reach the first
# address in the list. For the purpose of ACL used in the
# follow_x_forwarded_for directive the src ACL type always matches
# the address we are testing and srcdomain matches its rDNS.
#
# The end result of this process is an IP address that we will
# refer to as the indirect client address. This address may
# be treated as the client address for access control, ICAP, delay
# pools and logging, depending on the acl_uses_indirect_client,
# icap_uses_indirect_client, delay_pool_uses_indirect_client and
# log_uses_indirect_client options.
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
# SECURITY CONSIDERATIONS:
#
# Any host for which we follow the X-Forwarded-For header
# can place incorrect information in the header, and Squid
# will use the incorrect information as if it were the
# source address of the request. This may enable remote
# hosts to bypass any access control restrictions that are
# based on the client's source addresses.
#
# For example:
#
# acl localhost src 127.0.0.1
# acl my_other_proxy srcdomain .proxy.example.com
# follow_x_forwarded_for allow localhost
# follow_x_forwarded_for allow my_other_proxy
#Default:
# follow_x_forwarded_for deny all
# TAG: acl_uses_indirect_client on|off
# Controls whether the indirect client address
# (see follow_x_forwarded_for) is used instead of the
# direct client address in acl matching.
#
# NOTE: maxconn ACL considers direct TCP links and indirect
# clients will always have zero. So no match.
#Default:
# acl_uses_indirect_client on
# TAG: delay_pool_uses_indirect_client on|off
# Controls whether the indirect client address
# (see follow_x_forwarded_for) is used instead of the
# direct client address in delay pools.
#Default:
# delay_pool_uses_indirect_client on
# TAG: log_uses_indirect_client on|off
# Controls whether the indirect client address
# (see follow_x_forwarded_for) is used instead of the
# direct client address in the access log.
#Default:
# log_uses_indirect_client on
# TAG: http_access
# Allowing or Denying access based on defined access lists
#
# Access to the HTTP port:
# http_access allow|deny [!]aclname ...
http_access allow lanhome
#
# NOTE on default values:
#
# If there are no "access" lines present, the default is to deny
# the request.
#
# If none of the "access" lines cause a match, the default is the
# opposite of the last line in the list. If the last line was
# deny, the default is allow. Conversely, if the last line
# is allow, the default will be deny. For these reasons, it is a
# good idea to have an "deny all" entry at the end of your access
# lists to avoid potential confusion.
#
# This clause supports both fast and slow acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
#Default:
# http_access deny all
#
#
# Recommended minimum Access Permission configuration:
#
# Only allow cachemgr access from localhost
http_access allow manager localhost
http_access deny manager
# Deny requests to certain unsafe ports
# http_access deny !Safe_ports
# Deny CONNECT to other than secure SSL ports
http_access deny CONNECT !SSL_ports
# We strongly recommend the following be uncommented to protect innocent
# web applications running on the proxy server who think the only
# one who can access services on "localhost" is a local user
#http_access deny to_localhost
#
# INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS
#
# Example rule allowing access from your local networks.
# Adapt localnet in the ACL section to list your (internal) IP networks
# from where browsing should be allowed
#http_access allow localnet
http_access allow localhost
# And finally deny all other access to this proxy
http_access deny all
# TAG: adapted_http_access
# Allowing or Denying access based on defined access lists
#
# Essentially identical to http_access, but runs after redirectors
# and ICAP/eCAP adaptation. Allowing access control based on their
# output.
#
# If not set then only http_access is used.
#Default:
# none
# TAG: http_reply_access
# Allow replies to client requests. This is complementary to http_access.
#
# http_reply_access allow|deny [!] aclname ...
#
# NOTE: if there are no access lines present, the default is to allow
# all replies
#
# If none of the access lines cause a match the opposite of the
# last line will apply. Thus it is good practice to end the rules
# with an "allow all" or "deny all" entry.
#
# This clause supports both fast and slow acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#Default:
# none
# TAG: icp_access
# Allowing or Denying access to the ICP port based on defined
# access lists
#
# icp_access allow|deny [!]aclname ...
#
# See http_access for details
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
## Allow ICP queries from local networks only
##icp_access allow localnet
##icp_access deny all
#Default:
# icp_access deny all
# TAG: htcp_access
# Allowing or Denying access to the HTCP port based on defined
# access lists
#
# htcp_access allow|deny [!]aclname ...
#
# See http_access for details
#
# NOTE: The default if no htcp_access lines are present is to
# deny all traffic. This default may cause problems with peers
# using the htcp or htcp-oldsquid options.
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
## Allow HTCP queries from local networks only
##htcp_access allow localnet
##htcp_access deny all
#Default:
# htcp_access deny all
# TAG: htcp_clr_access
# Allowing or Denying access to purge content using HTCP based
# on defined access lists
#
# htcp_clr_access allow|deny [!]aclname ...
#
# See http_access for details
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#
## Allow HTCP CLR requests from trusted peers
#acl htcp_clr_peer src 172.16.1.2
#htcp_clr_access allow htcp_clr_peer
#Default:
# htcp_clr_access deny all
# TAG: miss_access
# Determins whether network access is permitted when satisfying a request.
#
# For example;
# to force your neighbors to use you as a sibling instead of
# a parent.
#
# acl localclients src 172.16.0.0/16
# miss_access allow localclients
# miss_access deny !localclients
#
# This means only your local clients are allowed to fetch relayed/MISS
# replies from the network and all other clients can only fetch cached
# objects (HITs).
#
#
# The default for this setting allows all clients who passed the
# http_access rules to relay via this proxy.
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#Default:
# miss_access allow all
# TAG: ident_lookup_access
# A list of ACL elements which, if matched, cause an ident
# (RFC 931) lookup to be performed for this request. For
# example, you might choose to always perform ident lookups
# for your main multi-user Unix boxes, but not for your Macs
# and PCs. By default, ident lookups are not performed for
# any requests.
#
# To enable ident lookups for specific client addresses, you
# can follow this example:
#
# acl ident_aware_hosts src 198.168.1.0/24
# ident_lookup_access allow ident_aware_hosts
# ident_lookup_access deny all
#
# Only src type ACL checks are fully supported. A srcdomain
# ACL might work at times, but it will not always provide
# the correct result.
#
# This clause only supports fast acl types.
# See http://wiki.squid-cache.org/SquidFaq/SquidAcl for details.
#Default:
# ident_lookup_access deny all
# TAG: reply_body_max_size size [acl acl...]
# This option specifies the maximum size of a reply body. It can be
# used to prevent users from downloading very large files, such as
# MP3's and movies. When the reply headers are received, the
# reply_body_max_size lines are processed, and the first line where
# all (if any) listed ACLs are true is used as the maximum body size
# for this reply.
#
# This size is checked twice. First when we get the reply headers,
# we check the content-length value. If the content length value exists
# and is larger than the allowed size, the request is denied and the
# user receives an error message that says "the request or reply
# is too large." If there is no content-length, and the reply
# size exceeds this limit, the client's connection is just closed
# and they will receive a partial reply.
#
# WARNING: downstream caches probably can not detect a partial reply
# if there is no content-length header, so they will cache
# partial responses and give them out as hits. You should NOT
# use this option if you have downstream caches.
#
# WARNING: A maximum size smaller than the size of squid's error messages
# will cause an infinite loop and crash squid. Ensure that the smallest
# non-zero value you use is greater that the maximum header size plus
# the size of your largest error page.
#
# If you set this parameter none (the default), there will be
# no limit imposed.
#
# Configuration Format is:
# reply_body_max_size SIZE UNITS [acl ...]
# ie.
# reply_body_max_size 10 MB
#
#Default:
# none
# NETWORK OPTIONS
# -----------------------------------------------------------------------------
# TAG: http_port
# Usage: port [options]
# hostname:port [options]
# 1.2.3.4:port [options]
#
# The socket addresses where Squid will listen for HTTP client
# requests. You may specify multiple socket addresses.
# There are three forms: port alone, hostname with port, and
# IP address with port. If you specify a hostname or IP
# address, Squid binds the socket to that specific
# address. This replaces the old 'tcp_incoming_address'
# option. Most likely, you do not need to bind to a specific
# address, so you can use the port number alone.
#
# If you are running Squid in accelerator mode, you
# probably want to listen on port 80 also, or instead.
#
# The -a command line option may be used to specify additional
# port(s) where Squid listens for proxy request. Such ports will
# be plain proxy ports with no options.
#
# You may specify multiple socket addresses on multiple lines.
#
# Options:
#
# intercept Support for IP-Layer interception of
# outgoing requests without browser settings.
# NP: disables authentication and IPv6 on the port.
#
# tproxy Support Linux TPROXY for spoofing outgoing
# connections using the client IP address.
# NP: disables authentication and maybe IPv6 on the port.
#
# accel Accelerator mode. Also needs at least one of
# vhost / vport / defaultsite.
#
# allow-direct Allow direct forwarding in accelerator mode. Normally
# accelerated requests are denied direct forwarding as if
# never_direct was used.
#
# defaultsite=domainname
# What to use for the Host: header if it is not present
# in a request. Determines what site (not origin server)
# accelerators should consider the default.
# Implies accel.
#
# vhost Accelerator mode using Host header for virtual domain support.
# Also uses the port as specified in Host: header unless
# overridden by the vport option. Implies accel.
#
# vport Virtual host port support. Using the http_port number
# instead of the port passed on Host: headers. Implies accel.
#
# vport=NN Virtual host port support. Using the specified port
# number instead of the port passed on Host: headers.
# Implies accel.
#
# protocol= Protocol to reconstruct accelerated requests with.
# Defaults to http.
#
# ignore-cc Ignore request Cache-Control headers.
#
# Warning: This option violates HTTP specifications if
# used in non-accelerator setups.
#
# connection-auth[=on|off]
# use connection-auth=off to tell Squid to prevent
# forwarding Microsoft connection oriented authentication
# (NTLM, Negotiate and Kerberos)
#
# disable-pmtu-discovery=
# Control Path-MTU discovery usage:
# off lets OS decide on what to do (default).
# transparent disable PMTU discovery when transparent
# support is enabled.
# always disable always PMTU discovery.
#
# In many setups of transparently intercepting proxies
# Path-MTU discovery can not work on traffic towards the
# clients. This is the case when the intercepting device
# does not fully track connections and fails to forward
# ICMP must fragment messages to the cache server. If you
# have such setup and experience that certain clients
# sporadically hang or never complete requests set
# disable-pmtu-discovery option to 'transparent'.
#
# ssl-bump Intercept each CONNECT request matching ssl_bump ACL,
# establish secure connection with the client and with
# the server, decrypt HTTP messages as they pass through
# Squid, and treat them as unencrypted HTTP messages,
# becoming the man-in-the-middle.
#
# When this option is enabled, additional options become
# available to specify SSL-related properties of the
# client-side connection: cert, key, version, cipher,
# options, clientca, cafile, capath, crlfile, dhparams,
# sslflags, and sslcontext. See the https_port directive
# for more information on these options.
#
# The ssl_bump option is required to fully enable
# the SslBump feature.
#
# name= Specifies a internal name for the port. Defaults to
# the port specification (port or addr:port)
#
# tcpkeepalive[=idle,interval,timeout]
# Enable TCP keepalive probes of idle connections.
# In seconds; idle is the initial time before TCP starts
# probing the connection, interval how often to probe, and
# timeout the time before giving up.
#
# If you run Squid on a dual-homed machine with an internal
# and an external interface we recommend you to specify the
# internal address:port in http_port. This way Squid will only be
# visible on the internal address.
#
#
# Squid normally listens to port 3128
http_port 3128
# TAG: https_port
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# Usage: [ip:]port cert=certificate.pem [key=key.pem] [options...]
#
# The socket address where Squid will listen for HTTPS client
# requests.
#
# This is really only useful for situations where you are running
# squid in accelerator mode and you want to do the SSL work at the
# accelerator level.
#
# You may specify multiple socket addresses on multiple lines,
# each with their own SSL certificate and/or options.
#
# Options:
#
# accel Accelerator mode. Also needs at least one of
# defaultsite or vhost.
#
# defaultsite= The name of the https site presented on
# this port. Implies accel.
#
# vhost Accelerator mode using Host header for virtual
# domain support. Requires a wildcard certificate
# or other certificate valid for more than one domain.
# Implies accel.
#
# protocol= Protocol to reconstruct accelerated requests with.
# Defaults to https.
#
# cert= Path to SSL certificate (PEM format).
#
# key= Path to SSL private key file (PEM format)
# if not specified, the certificate file is
# assumed to be a combined certificate and
# key file.
#
# version= The version of SSL/TLS supported
# 1 automatic (default)
# 2 SSLv2 only
# 3 SSLv3 only
# 4 TLSv1 only
#
# cipher= Colon separated list of supported ciphers.
# NOTE: some ciphers such as EDH ciphers depend on
# additional settings. If those settings are
# omitted the ciphers may be silently ignored
# by the OpenSSL library.
#
# options= Various SSL engine options. The most important
# being:
# NO_SSLv2 Disallow the use of SSLv2
# NO_SSLv3 Disallow the use of SSLv3
# NO_TLSv1 Disallow the use of TLSv1
# SINGLE_DH_USE Always create a new key when using
# temporary/ephemeral DH key exchanges
# See OpenSSL SSL_CTX_set_options documentation for a
# complete list of options.
#
# clientca= File containing the list of CAs to use when
# requesting a client certificate.
#
# cafile= File containing additional CA certificates to
# use when verifying client certificates. If unset
# clientca will be used.
#
# capath= Directory containing additional CA certificates
# and CRL lists to use when verifying client certificates.
#
# crlfile= File of additional CRL lists to use when verifying
# the client certificate, in addition to CRLs stored in
# the capath. Implies VERIFY_CRL flag below.
#
# dhparams= File containing DH parameters for temporary/ephemeral
# DH key exchanges. See OpenSSL documentation for details
# on how to create this file.
# WARNING: EDH ciphers will be silently disabled if this
# option is not set.
#
# sslflags= Various flags modifying the use of SSL:
# DELAYED_AUTH
# Don't request client certificates
# immediately, but wait until acl processing
# requires a certificate (not yet implemented).
# NO_DEFAULT_CA
# Don't use the default CA lists built in
# to OpenSSL.
# NO_SESSION_REUSE
# Don't allow for session reuse. Each connection
# will result in a new SSL session.
# VERIFY_CRL
# Verify CRL lists when accepting client
# certificates.
# VERIFY_CRL_ALL
# Verify CRL lists for all certificates in the
# client certificate chain.
#
# sslcontext= SSL session ID context identifier.
#
# generate-host-certificates[=<on|off>]
# Dynamically create SSL server certificates for the
# destination hosts of bumped CONNECT requests.When
# enabled, the cert and key options are used to sign
# generated certificates. Otherwise generated
# certificate will be selfsigned.
# If there is CA certificate life time of generated
# certificate equals lifetime of CA certificate. If
# generated certificate is selfsigned lifetime is three
# years.
# This option is enabled by default when SslBump is used.
# See the sslBump option above for more information.
#
# dynamic_cert_mem_cache_size=SIZE
# Approximate total RAM size spent on cached generated
# certificates. If set to zero, caching is disabled. The
# default value is 4MB. An average XXX-bit certificate
# consumes about XXX bytes of RAM.
#
# vport Accelerator with IP based virtual host support.
#
# vport=NN As above, but uses specified port number rather
# than the https_port number. Implies accel.
#
# name= Specifies a internal name for the port. Defaults to
# the port specification (port or addr:port)
#
#Default:
# none
# TAG: tcp_outgoing_tos
# Allows you to select a TOS/Diffserv value to mark outgoing
# connections with, based on the username or source address
# making the request.
#
# tcp_outgoing_tos ds-field [!]aclname ...
#
# Example where normal_service_net uses the TOS value 0x00
# and good_service_net uses 0x20
#
# acl normal_service_net src 10.0.0.0/24
# acl good_service_net src 10.0.1.0/24
# tcp_outgoing_tos 0x00 normal_service_net
# tcp_outgoing_tos 0x20 good_service_net
#
# TOS/DSCP values really only have local significance - so you should
# know what you're specifying. For more information, see RFC2474,
# RFC2475, and RFC3260.
#
# The TOS/DSCP byte must be exactly that - a octet value 0 - 255, or
# "default" to use whatever default your host has. Note that in
# practice often only multiples of 4 is usable as the two rightmost bits
# have been redefined for use by ECN (RFC 3168 section 23.1).
#
# Processing proceeds in the order specified, and stops at first fully
# matching line.
#
# Note: The use of this directive using client dependent ACLs is
# incompatible with the use of server side persistent connections. To
# ensure correct results it is best to set server_persisten_connections
# to off when using this directive in such configurations.
#Default:
# none
# TAG: clientside_tos
# Allows you to select a TOS/Diffserv value to mark client-side
# connections with, based on the username or source address
# making the request.
#Default:
# none
# TAG: qos_flows
# Allows you to select a TOS/DSCP value to mark outgoing
# connections with, based on where the reply was sourced.
#
# TOS values really only have local significance - so you should
# know what you're specifying. For more information, see RFC2474,
# RFC2475, and RFC3260.
#
# The TOS/DSCP byte must be exactly that - octet value 0x00-0xFF.
# Note that in practice often only values up to 0x3F are usable
# as the two highest bits have been redefined for use by ECN
# (RFC3168).
#
# This setting is configured by setting the source TOS values:
#
# local-hit=0xFF Value to mark local cache hits.
#
# sibling-hit=0xFF Value to mark hits from sibling peers.
#
# parent-hit=0xFF Value to mark hits from parent peers.
#
#
# NOTE: 'miss' preserve feature is only possible on Linux at this time.
#
# For the following to work correctly, you will need to patch your
# linux kernel with the TOS preserving ZPH patch.
# The kernel patch can be downloaded from http://zph.bratcheda.org
#
# disable-preserve-miss
# By default, the existing TOS value of the response coming
# from the remote server will be retained and masked with
# miss-mark. This option disables that feature.
#
# miss-mask=0xFF
# Allows you to mask certain bits in the TOS received from the
# remote server, before copying the value to the TOS sent
# towards clients.
# Default: 0xFF (TOS from server is not changed).
#
#Default:
# none
# TAG: tcp_outgoing_address
# Allows you to map requests to different outgoing IP addresses
# based on the username or source address of the user making
# the request.
#
# tcp_outgoing_address ipaddr [[!]aclname] ...
#
# Example where requests from 10.0.0.0/24 will be forwarded
# with source address 10.1.0.1, 10.0.2.0/24 forwarded with
# source address 10.1.0.2 and the rest will be forwarded with
# source address 10.1.0.3.
#
# acl normal_service_net src 10.0.0.0/24
# acl good_service_net src 10.0.2.0/24
# tcp_outgoing_address 10.1.0.1 normal_service_net
# tcp_outgoing_address 10.1.0.2 good_service_net
# tcp_outgoing_address 10.1.0.3
#
# Processing proceeds in the order specified, and stops at first fully
# matching line.
#
# Note: The use of this directive using client dependent ACLs is
# incompatible with the use of server side persistent connections. To
# ensure correct results it is best to set server_persistent_connections
# to off when using this directive in such configurations.
#
#
# IPv6 Magic:
#
# Squid is built with a capability of bridging the IPv4 and IPv6
# internets.
# tcp_outgoing_address as exampled above breaks this bridging by forcing
# all outbound traffic through a certain IPv4 which may be on the wrong
# side of the IPv4/IPv6 boundary.
#
# To operate with tcp_outgoing_address and keep the bridging benefits
# an additional ACL needs to be used which ensures the IPv6-bound traffic
# is never forced or permitted out the IPv4 interface.
#
# # IPv6 destination test along with a dummy access control to perofrm the required DNS
# # This MUST be place before any ALLOW rules.
# acl to_ipv6 dst ipv6
# http_access deny ipv6 !all
#
# tcp_outgoing_address 2001:db8::c001 good_service_net to_ipv6
# tcp_outgoing_address 10.1.0.2 good_service_net !to_ipv6
#
# tcp_outgoing_address 2001:db8::beef normal_service_net to_ipv6
# tcp_outgoing_address 10.1.0.1 normal_service_net !to_ipv6
#
# tcp_outgoing_address 2001:db8::1 to_ipv6
# tcp_outgoing_address 10.1.0.3 !to_ipv6
#
# WARNING:
# 'dst ipv6' bases its selection assuming DIRECT access.
# If peers are used the peername ACL are needed to select outgoing
# address which can link to the peer.
#
# 'dst ipv6' is a slow ACL. It will only work here if 'dst' is used
# previously in the http_access rules to locate the destination IP.
# Some more magic may be needed for that:
# http_access allow to_ipv6 !all
# (meaning, allow if to IPv6 but not from anywhere ;)
#
#Default:
# none
# SSL OPTIONS
# -----------------------------------------------------------------------------
# TAG: ssl_unclean_shutdown
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# Some browsers (especially MSIE) bugs out on SSL shutdown
# messages.
#Default:
# ssl_unclean_shutdown off
# TAG: ssl_engine
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# The OpenSSL engine to use. You will need to set this if you
# would like to use hardware SSL acceleration for example.
#Default:
# none
# TAG: sslproxy_client_certificate
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# Client SSL Certificate to use when proxying https:// URLs
#Default:
# none
# TAG: sslproxy_client_key
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# Client SSL Key to use when proxying https:// URLs
#Default:
# none
# TAG: sslproxy_version
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# SSL version level to use when proxying https:// URLs
#Default:
# sslproxy_version 1
# TAG: sslproxy_options
# Note: This option is only available if Squid is rebuilt with the
# --enable-ssl option
#
# SSL engine options to use when proxying https:// URLs
#
# The most important being:
#
# NO_SSLv2 Disallow the use of SSLv2
# NO_SSLv3 Disallow the use of SSLv3
# NO_TLSv1 Disallow the use of TLSv1
# SINGLE_DH_USE
# Always create a new key when using
# temporary/ephemeral DH key exchanges
#
# These options vary depending on your SSL engine.
# See the OpenSSL SSL_CTX_set_options documentation for a
# complete list of possible options.
#Default
